Sanyo MCO-19M - Page 40

- 37 -
䣑䣍
䣷䣵䣕䣶 䣣 䣶
䣖䣱䣱 䣮 䣵
䣎䣱䣩
䣕䣧 䣶
䢷䢰䢲䢲䢵䢹 䢰
䣗䣏䣇䣐
䣑䢴䢰䢲䢧䢴䢷䣅䣑䢰䢲䤑䣅䣲䢵䢹䣖䣧䣯
䣧䣖䣫䣯䣆䣣䣶 䣧
䣫䣰䣩䣕䣧䣶 䣶䣒䣙䣎䣱䣥䣭䣍䣧䣻
䣰䣩䣧䣶䣶 䣫䣗䣘 䣕
䣥䣧䣮䣅䣣 䣰
䣫䣰䣩䣕䣧 䣶 䣶䣆䣃䣓䣎䣅䣆䢱
䣕䣸 䣥
䣫䣰䣩䣕䣧 䣶 䣶䣣䣴䣯
䣑
䣃䣮
䣍
䣰䣣䣶 䣫䣱䣮䣫䣤䣴䢴䣅䣣䣑䢴 䢱䣑䣯䣲䢱䣅䣖䣧
䣗䣏䣇䣐
䢫䢪䢳䢱䢴䣱䣮䣵䣶䣖䣱䣧䣮䣧䣥䣕
䣃䣮䣣䣴䣯 䣕䣧䣶 䣶 䣫䣰䣩
䣖䣧䣯䣲 䣃䣮 䣣 䣴䣯 䤒 䢳䢰䢲 䣅 䢪䤒䢳 䢰 䢲 䣅 䢯 䤒䢷 䢰 䢲 䣅 䢫
䣅䣑 䢴 䣃 䣮 䣣 䣴 䣯 䤒 䢳 䢰 䢲 䢧 䢪䤒䢲 䢰 䢷 䢧 䢯 䤒䢷 䢰 䢲 䢧 䢫
䣑䢴 䣃䣮 䣣䣴䣯 䤒 䢳 䢰䢲䢧 䢪䤒䢲䢰 䢷䢧 䢯 䤒䢷 䢰䢲䢧 䢫
䣃䣮䣣䣴䣯 䣆䣧䣮䣣䣻 䢳䢷䣯䣫䣰 䢪䢲䢯䢳䢷䣯䣫䣰䢫
䣔䣫䣰䣩 䣄䣣䣥䣭 䢵䢲䣯䣫䣰 䢪䢲䢰䣑䣈䣈 䢳䢯䢻䢻䣯䣫䣰䢫
䣆䣱䣱 䣴 䣆䣧 䣮 䣣 䣻 䢴䣯䣫 䣰 䢪 䢳䢯䢵䢲䣯䣫 䣰 䢫
㻌
㻌
㻌
㻌
<Alarm delay time>
Setting range of both alarm delay time for high/low temperature alarms, and high/low CO2 density alarms is 0~15 minutes.
(Factory default: 15 minutes)
Setting range of high /low O2 density alarm is 0~30 minutes. (Factory default: 30 minutes)
O2 density alarm will emit after twice of setting time elapses
.
Note) Even if you input a value more than 15 minutes, alarm delay time will be set in 15 minutes.
<Ring Back time>
Setting range is 1~99 minutes. (Factory default: 30 minutes)
<Door open alarm delay time>
When an outer door leaves open, an audible alarm sounds after predetermined time elapsed.
Setting range of door open alarm delay time is 1~30 minutes. (Factory default: 2 minutes)
Note) When you input “0” minute, door open alarm delay time will be set in 1 minute.
Even if you input a value more than 30 minutes, door open alarm delay time will be set in 30 minutes.