- 57 -
䣣䣦䣣䣶䣮䣫䣼䣧䣋䣰䣫䣶䣫䣣
䣕䣶䣣䣶䣷䣵
䣶䣫䣰䣩䣕䣧 䣶䣧䣥䣱䣰䣆
䣧䣮䣣䣰䣥䣴䣄䣣䣧䣣 䣶䣧䣊
䣅䣣 䣰䣥 䣧 䣮
䣥䣰䣧䣶䣣䣶 䣫䣱䣮䣫䣤䣴䣩䣅䣣䣰䣣 䣮 䣱䣃
䣑䣍
䣫䣱䣰䣷䣴䣣䣶䣰䣨 䣫䣩䣯䣅䣱䣻䣵 䣶䣧䣕
䣏䣇䣐䣗
䢲䣃䢰䢳䢰䢳䣘䣧 䣴䣕䣸 䣥䣱䣮䣵䣶䣖䣱䣕䣧 䣮 䣧䣥
䣗䣏䣇䣐
䣥䣧䣮䣅䣣 䣰
䣑䣍
䢻䢫䢲䢯䢪䢸䣧䣴䣊䣧 䣣 䣶䣱䣱 䣴䣆
䢶䢲 䢫䢲䢯䢪䢸䣴䣧䣣䣶䣧䣗䣏 䣊䣊
䣧䣮䣣䣰䣥䣴䣄䣣䣧䣣 䣶䣧䣊
㻌
㻌
㻌
13. Setting of H2O2 decontamination time
㻌
㻌
䣣䣦 䣣 䣶䣮 䣫 䣼 䣧䣋 䣰 䣫 䣶 䣫 䣣
䣕 䣶 䣣 䣶 䣷 䣵
䣶 䣫 䣰 䣩䣕 䣧 䣶䣆 䣧 䣥 䣱 䣰
䣧䣮 䣣 䣰 䣥䣴 䣄 䣣䣊 䣧 䣣 䣶 䣧
䣅 䣣 䣰 䣥 䣧 䣮
䣥䣰 䣧 䣶䣣 䣶 䣫 䣱䣮 䣫 䣤 䣴䣩 䣅 䣣䣰 䣣 䣮 䣱䣃
䣑 䣍
䣱 䣰䣴 䣣 䣶 䣫䣨 䣫 䣩 䣷䣕 䣻 䣵 䣶 䣧 䣯 䣅 䣱 䣰
䣏 䣇 䣐 䣗
䣃䢳 䢰 䢳 䢲
䣘 䣧 䣴 䢰䣸 䣥䣮 䣵 䣕䣖 䣱 䣱䣕 䣧 䣮 䣧 䣥 䣶
㻌
㻌
㻌
㻌
䣆 䣧 䣥 䣱 䣰 䣕 䣧 䣶 䣶 䣫 䣰 䣩
䣆 䣧 䣥 䣱 䣰 䣖 䣧 䣯 䣲 䢶 䢷 䢰 䢲 䤑䣅 䢪 䢵 䢹 䢰 䢲
䣅 䢫
䣆 䣧 䣥 䣱 䣰 䣖 䣫 䣯 䣧 䢳 䢹 䣯 䣫 䣰 䢪 䢳 䢯 䢵 䢲 䣯 䣫
䢴 䢲
䣰 䢫
䣍 䣧 䣧 䣲 䣖 䣫 䣯 䣧 䢳 䢲 䣯 䣫 䣰 䢪 䢲 䢯 䢳
䣆 䣧 䣥 䣱 䣰 䣖 䣫 䣯 䣧 䢴 䢲 䣯 䣫 䣰 䢪 䢲 䢯 䢵 䢲 䣯 䣫 䣰 䢫
䣗 䣘 䣔 䣧 䣵 䣱 䣮 䣸 䣧 䢴 䢻 䢲 䣯 䣫 䣰 䢪 䢵 䢲 䢯 䢵 䢸 䢲 䣯 䣫 䣰 䢫
䢺
䣯 䣫 䣰 䢫
㻌
㻌
㻌 <Setting of H2O2 decontamination temperature>
㻌㻌㻌㻌㻌
An apparatus stands by for H2O2 decontamination until it reaches decontamination set temperature +/- 1.0䉝.
Setting range is 37.0~48.0䉝. (Factory default; 45.0䉝)
㻌㻌㻌㻌
㻌㻌㻌㻌Note) When you input a value lower than 37.0䉝, H2O2 decontamination temperature is automatically set in 37.0䉝.
When you input a value higher than 48.0䉝, H2O2 decontamination temperature is automatically set in 48.0䉝.
<Setting of primary H2O2 misting time>
When an apparatus steps to primary H2O2 misting process, ultrasonic oscillator will be active.
Setting range is 1~30 minutes. (Factory default: 7 minutes)
Note) When you input a value lower than “1”, primary H2O2 misting time is automatically set in 1 minute.
When you input a value higher than “30”, primary H2O2 misting time is automatically set in 30 minutes.
Note) When water sensor signal turns off (H2O2 solution s lower than standard) during primary H2O2
misting process, an apparatus steps to secondary resolution process without commenceing
primary H2O2 preservation process and secondary H2O2 misting process.
㻌㻌<Setting of primary H2O2 preserved time>
Setting range is 0~120 minutes. (Factory default: 0 minute)
Note) When you input a value higher than 䇾120䇿, primary H2O2 preserved time is automatically set in 120 minutes.
<Setting of secondary H2O2 misting time>
When water sensor signal turns off (H2O2 solution is lower than standard) or it elapses 15 minutes since secondary
H2O2 misting time expires during secondary H2O2 misting process, an apparatus steps to secondary H2O2
resolution process.
Setting range is 0~30 minutes. (Factory default: 0 minutes)
Note) When you input a value higher than 䇾30䇿, secondary H2O2 misting time is automatically set in 30 minutes.
<Setting of secondary H2O2 resolution time>
Setting range is 30~360 minutes. (Factory default: 90 minutes)
Note) When you input a value lower than 30 minutes, secondary H2O2 resolution time is automatically set in 30minutes.
When you input a value higher than 360minutes, secondary H2O2 resolution time is automatically set in 360minutes.
To Next Page
Loading...
