Sanyo MCO-19M - Temperature, CO2, and O2 Calibration; Performing Sensor Calibration

- 56 -
㻌
㻌
㻌
12. Adjustment of heater balance
㻌
㻌
䣣䣦 䣣 䣶䣮 䣫 䣼 䣧䣋 䣰 䣫 䣶 䣫 䣣
䣕 䣶 䣣 䣶 䣷 䣵
䣶 䣫 䣰 䣩䣕 䣧 䣶䣧 䣥 䣱 䣰䣆
䣧䣮 䣣 䣰 䣥䣴 䣄 䣣䣧 䣣 䣶 䣧䣊
䣅 䣣 䣰 䣥 䣧 䣮
䣥䣰 䣧 䣶䣣 䣶 䣫 䣱䣮 䣫 䣤 䣴䣩 䣅 䣣䣰 䣣 䣮 䣱䣃
䣑 䣍
䣫 䣱 䣰䣷 䣴 䣣 䣶䣰 䣨 䣫 䣩䣯 䣅 䣱䣻 䣵 䣶 䣧䣕
䣏 䣇 䣐 䣗
䢲 䣃䢰 䢳 䢰
䢳䣘 䣧 䣴䣕 䣸 䣥䣱 䣮 䣵䣶 䣖 䣱䣕 䣧 䣮 䣧 䣥
㻌
㻌
㻌
㻌
䣗䣏 䣇 䣐
䣥 䣧 䣮䣅 䣣 䣰
䣑 䣍
䢻 䢫䢲 䢯䢪䢸䣧 䣴䣊 䣧 䣣 䣶䣱 䣱 䣴䣆
䢶 䢲 䢫䢲 䢯䢪䢸䣴䣧 䣣 䣶 䣧䣗 䣏 䣊䣊
䣧䣮 䣣 䣰 䣥䣴 䣄 䣣䣧 䣣 䣶 䣧䣊
㻌
㻌
<Adjustment of balance in bottom heater>㻌
Bottom heater output value can be changed for the prevention of chamber condensation
or when increasing chamber humidity.
Setting range is “0~40”. (Factory default: “10”)
Note) When you input a value over “40”, bottom heater output value is automatically set in “40”.
㻌
㻌
㻌
<Adjustment of balance in door heater>
Door heater output value can be changed for the prevention of condensation on outer door.
Setting range is “0~9”. (Factory default: “6”)
Note) When you input a value over “9”, door heater output value is automatically set in “9”.

䣣䣦䣣䣶䣮䣫䣼䣧䣋䣰䣫䣶䣫䣣
䣕䣶䣣䣶䣷䣵
䣶䣫䣰䣩䣕䣧 䣶䣆䣧䣥䣱䣰
䣧䣮䣣䣰䣥䣴䣄䣣䣊䣧䣣 䣶䣧
䣅䣣 䣰䣥 䣧 䣮
䣥䣰䣧䣶䣣䣶 䣫䣱䣮䣫䣤䣴䣩䣅䣣䣰䣣 䣮 䣱䣃
䣑䣍
䣱䣰䣴䣣䣶䣫䣨䣫䣩䣷䣕䣻䣵 䣶䣧䣯 䣅䣱䣰
䣏䣇䣐䣗
䣃䢳䢰䢳䢲䣘䣧 䣴 䢰䣸䣥䣮䣵 䣕䣖䣱䣱䣕䣧 䣮 䣧䣥䣶
䣆䣧䣥䣱䣰 䣕䣧䣶 䣶 䣫䣰䣩
䣆䣧䣥䣱䣰 䣖䣧䣯䣲 䢶䢷 䢰 䢲䤑䣅 䢪 䢵 䢹 䢰 䢲 䣅 䢯 䢶 䢰 䢲 䣅 䢫
䣆䣧䣥䣱䣰䣖䣫䣯䣧䢳 䢹䣯䣫䣰 䢪䢳䢯䢵䢲䣯䣫
䢴䢲
䣰䢫
䣍䣧䣧䣲 䣖 䣫䣯䣧 䢳 䢲 䣯䣫 䣰 䢪 䢲䢯䢳
䣆䣧䣥䣱䣰䣖䣫䣯䣧䢴 䢲䣯䣫䣰 䢪䢲䢯䢵䢲䣯䣫䣰䢫
䣗䣘 䣔䣧䣵䣱 䣮 䣸䣧 䢴 䢻䢲 䣯䣫 䣰 䢪 䢵䢲䢯䢵䢸䢲䣯䣫 䣰 䢫
䢺
䣯䣫䣰 䢫