Sanyo MCO-19M - Page 62

- 59 -
㻌
㻌
㻌
15. Initialization of non-volatile memory
㻌
Procedures MENU key
0 In Top Screen, press MENU key and select “Tools”. Tools
1 Press ENTER key to display “Select Tools (1/2)” and press MENU key to select “Svc”. Svc
2 Press ENTER key to display “Password” and input service code “384”. OK
3 Press ENTER key to display “Select Tools Svc” and select “Analog Calibration etc”.
4 Press MENU key and select “OK”. OK
5 Press ENTER key to display “Analog Calibration etc” and input “925” in the right side of
“Function” column.
6 Press MENU key and select “OK”. OK
7 Press ENTER key to return to “Select Tools Svc” display. Select “Initialize data”.
8 Press MENU key and select “OK”. Press ENTER key to display “Confirmation”. OK
9 Press MENU key and select “OK” to commence initialization. OK
Press MENU key and select “Cancel” to cancel initialization. Cancel
10 After commencing initialization, a device automatically returns to Top Screen.
After cancelling initialization, a device returns to “Select Tools Svc”.
㻌
㻌
䣣䣦 䣣 䣶䣮 䣫 䣼 䣧䣋 䣰 䣫 䣶 䣫 䣣
䣵䣶 䣣 䣶 䣷䣕
䣶 䣫 䣰 䣩䣕 䣧 䣶䣧 䣥 䣱 䣰䣆
䣧䣮 䣣 䣰 䣥䣴 䣄 䣣䣧 䣣 䣶 䣧䣊
䣥 䣧 䣮䣅 䣣 䣰
䣥䣰 䣧 䣶䣣 䣶 䣫 䣱䣮 䣫 䣤 䣴䣩 䣅 䣣䣰 䣣 䣮 䣱䣃
䣑 䣍
䣫 䣱 䣰䣷 䣴 䣣 䣶䣰 䣨 䣫 䣩䣯 䣅 䣱䣻 䣵 䣶 䣧䣕
䣗䣏 䣇 䣐
䢲 䣃䢰 䢳 䢰
䢳䣘 䣧 䣴䣕 䣸 䣥䣱 䣮 䣵䣶 䣖 䣱䣧 䣮 䣧 䣥䣕
㻌
㻌
㻌
䣰 䣫 䣶 䢫䢴 䢷 䢰 䣋䣒 䣙 䢻䢳 䢲 䢳 䢰䢪䢻 䢴 䢷䣫 䣱 䣰䣷 䣰 䣥 䣶䣈
䢲䣅 䣱 䣦 䣧䣏 䣱 䣦 䣧 䣮
䢧䢲䣨 䣧䣘 䣎 䣫䣗
䢳 䢲 䢲䣩 䣑 䢴䣰 䣣 䣮 䣱䣃
䣅 䣣 䣰 䣥 䣧 䣮
䢳 䢲 䢲䢴䣩 䣅 䣑䣰 䣣 䣮 䣱䣃
䣑 䣍
䢳 䢲 䢲䣯 䣲䣩 䣖 䣧䣰 䣣 䣮 䣱䣃
䣏 䣇 䣐 䣗
䣥䣰 䣧 䣶䣣 䣶 䣫 䣱
䣮 䣫 䣤 䣴䣩 䣅 䣣䣰 䣣 䣮 䣱䣃
㻌
㻌
㻌
䢲 䣃䢰 䢳 䢰 䢳䣘 䣧 䣴䣸 䣥䣕䣖 䣱 䣱 䣮 䣵䣕 䣧 䣮 䣧 䣥 䣶
䣏 䣇 䣐 䣗
䣕 䣻 䣵 䣶 䣧 䣯 䣅 䣱 䣰 䣨 䣫 䣩 䣷 䣴 䣣 䣶 䣫 䣱 䣰
䣑 䣍
䣃 䣰 䣣 䣮 䣱 䣩 䣅 䣣 䣮 䣫 䣤 䣴 䣣 䣶 䣫 䣱 䣰 䣧 䣶 䣥
䣅 䣣 䣰 䣥 䣧 䣮
䣊 䣧 䣣 䣶 䣧 䣴 䣄 䣣 䣮 䣣 䣰 䣥 䣧
䣆 䣧 䣥 䣱 䣰 䣕 䣧 䣶 䣶 䣫 䣰 䣩
䣕 䣶
䣣 䣶 䣷 䣵
䣋 䣰 䣫 䣶 䣫 䣣 䣮 䣫 䣼 䣧 䣦 䣣 䣶 䣣
㻌
㻌
㻌
䣶 䣫 䣱 䣰䣴 䣯 䣣䣱 䣰 䣨 䣫䣅
䣃 䣴 䣧 䣻 䣱 䣷 䣵 䣷 䣴 䣧 䣶 䣱 䣦 䣧 䣮 䣧 䣶 䣧 䣁
䣑 䣍
䣅 䣣 䣰 䣥 䣧 䣮
䣃 䣮 䣮 䣗 䣵 䣧 䣴 䣐 䣣 䣯 䣧 䣵 䣣 䣰 䣦 䣒 䣴 䣱 䣩 䣴 䣣 䣯 䣵
䣏 䣇 䣐 䣗
㻌
㻌
㻌