Sanyo PLC-XU116

-41-
Electrical Adjustments
Group/
Item
Item Name Function Initial Range Note
220 BLANK_RCENTER 0 0-2047
221 BLANK_RSTART 128 0-255
222 BLANK_REND 128 0-255
223 BLANK_GCENTER 0 0-2047
224 BLANK_GSTART 128 0-255
225 BLANK_GEND 128 0-255
226 BLANK_BCENTER 0 0-2047
227 BLANK_BSTART 128 0-255
228 BLANK_BEND 128 0-255
229 Output limit R 4095 0-4095
230 Output limit G 4095 0-4095
231 Output limit B 4095 0-4095
232 CROSSTALK_COEF_R 1023 0-1023
233 CROSSTALK_COEF_G 1023 0-1023
234 CROSSTALK_COEF_B 1023 0-1023
235 LCCON_ENABL 0 0-1
236 ENBY_L1 12 0-255
237 ENBY_H1 675 0-1026
238 ENBY_L2 12 0-255
239 ENBY_H2 675 0-1023
Group101 : Panel Service(6150/1060)
0 R-LCCOM
135 0-255
1 G-LCCOM
135 0-255
2 B-LCCOM 135 0-255
3 R-ENBX-PW 4 0-15
4 G-ENBX-PW 4 0-15
5 B-ENBX-PW 4 0-15
6 R-DXIN 38 28-64
7 G-DXIN 38 28-64
8 B-DXIN 38 28-64
9 R-ENBX1IN 17 0-31
10 G-ENBX1IN 17 0-31
11 B-ENBX1IN 17 0-31
12 Vmid 146 0-255
13 R-Ref 150 0-255
14 G-Ref 150 0-255
15 B-Ref 150 0-255
Group102 : Auto Keystone Setup Value
0 OFFSET 0
-1056 -
1056
1 OFFSET SWITCH
0
0 - 1
2 DEBUG MODE
0
0 - 1
3 SERVICE CALIBRATION
0
0 - 1
4 LOCK COUNT
5
1 - 255
5 DELT VERT RESULT
64
1 - 255
6 ANGLE 1 COUNT
1
1 - 10
7 ANGLE 2 COUNT
5
1 - 10
8 BLIND SECTOR 1
160
0 - 1024
9 BLIND SECTOR 3
32
0 - 1024
10 BLIND SECTOR BIAS
61
0 - 1024
Group
200
Option
0
Logo Prohibition (Forced No
Brand)
Logo Prohibition (0: Menu, 1: Forced,
2: China, 3-9: not used)
0 0 - 2 Effective after AC On
1 RS232C Baudrate Baud Rate 0 0 - 2
0: 19200bps, 1: 9600bps, 2:
115200bps
4 CABLE SW Long Cable 0 0 - 10 0: Disable, 1: Enable
5
PW Debug Command
Enable
0 0 - 1
0:Disable (Serial Command Eanble)
1: Enable (PW Debug Mode)
6 Device Refresh Disable 0 0 - 1
0:Enable, 1:Disable
No last memory
7 Device Access Disable 0 0 - 1
0:Enable (Normal), 1:Disable
No last memory
9 PJ-NET MCU test enable 0 0 - 1 0: Enable, 1: Disable
30 Lamp life test enable
0:Disable 1:Enable, for safety test
only
31 Lamp On time(for life test) For test purpose
32 Lamp Off time(for life test) For test purpose