SCHUNK PWG-S 40 User Manual (English)

Other manuals for SCHUNK PWG-S 40

Questions and Answers:

R
richard26Aug 16, 2025
Why is the gripping force dropping on my SCHUNK PWG-S 40 Power Tool?
- A
  Ashley WarnerAug 16, 2025
  If the SCHUNK Power Tool's gripping force is dropping, it could be due to several reasons. First, check the seals for leaks; if needed, disassemble the product and replace the seals. Another potential cause is excessive grease in the mechanical movement area, in which case you should clean and lubricate the product. Also, ensure that the air supply is adequate and that the pressure isn't dropping below the minimum required. If none of these steps resolve the issue, a component part may be defective, requiring replacement or repair by SCHUNK.
K
Kimberly GreeneAug 19, 2025
What to do if compressed air lines are switched in SCHUNK Industrial Equipment?
- C
  Chris HinesAug 19, 2025
  If you suspect the compressed air lines are switched, check the compressed air lines to ensure they are correctly connected.
R
roblescharlesAug 22, 2025
What to do if SCHUNK Industrial Equipment component is broken?
- M
  meyerbrandyAug 22, 2025
  If a component is broken, for example, due to overloading, replace the component or send the module with a repair order to SCHUNK. Also, ensure that the module was only used within its defined application parameters.
J
Jonathan JenningsAug 25, 2025
What to do if pressure drops below minimum in SCHUNK Industrial Equipment?
- L
  louis75Aug 26, 2025
  If the pressure drops below the minimum required, check the air supply to ensure it meets the necessary levels.
P
Peter ClarkAug 28, 2025
What to do if unused air connections are not closed in SCHUNK Industrial Equipment?
- W
  William OwensAug 28, 2025
  If you find that unused air connections are open, close them to maintain proper system pressure and function.
J
jenniferandersonAug 31, 2025
What to do if piston jams in SCHUNK Industrial Equipment?
- J
  Jason SmithAug 31, 2025
  If the piston jams, potentially due to excessive load, check the permissible mass and length of the top jaws to ensure they are within the specified limits.
J
Joseph MendezSep 3, 2025
How to fix base jaws that jam in housing of SCHUNK Industrial Equipment?
- M
  Marissa RussellSep 3, 2025
  If the base jaws jam in the housing, it may be due to the bolting surface not being sufficiently level. Check the levelness of the bolting surface. Loosen the mounting screws for the gripper and actuate the gripper again.
C
Cody WebsterSep 6, 2025
What to do if proximity switch is defective in SCHUNK Industrial Equipment?
- J
  Jessica KimSep 6, 2025
  If the proximity switch is defective or set incorrectly, repair the proximity switch.
J
Jessica MoonSep 9, 2025
How to troubleshoot a SCHUNK PWG-S 40 Power Tool that does not move?
- R
  richard54Sep 9, 2025
  If your SCHUNK Power Tool isn't moving, start by checking the evenness of the mounting surface, as unevenness can cause the base jaws to jam. Ensure that the air supply is sufficient and the pressure isn't below the minimum requirement. Verify that the compressed air lines are correctly connected and that no lines are switched. Inspect the proximity switch for defects or incorrect settings, readjusting or replacing the sensor if necessary. Also, close any unused air connections and open the flow control valve. If the issue persists, a component part may be defective, and you should replace it or send the tool to SCHUNK for repair.
C
christopher02Sep 12, 2025
What to do if my SCHUNK PWG-S 40 Power Tool is not executing the complete stroke?
- T
  Todd LeeSep 12, 2025
  If your SCHUNK Power Tool isn't completing its full stroke, it could be due to dirt accumulation. Try cleaning and re-lubricating the area between the cover and piston. Also, disassemble and clean the product to remove any dirt between the basic jaws and guidance. Ensure that the air supply is sufficient and the pressure isn't dropping below the minimum requirement. Check the evenness of the mounting surface. If the issue continues, a component part may be defective, which would require replacement or sending the tool to SCHUNK for repair.