Watching TV
Turning
On/Off
the
Power
trr~~~===~~
TV POWER
I
Tvj
TV
VCR
Aumo
'I
(On/Standby)
I
IJ
CB~SAT
o~o
FU~ON
I
\
SOURCE
LIGHT I
88CIDI
I~
II
I
I.I~
ill
.----:r
!---.
~WER
I
'In
POWER
MENU
o
INPUT
o
Press POWER on the
N,
or TV POWER on the remote control unit to
turn the power on.
• POWER indicator (Blue): The
lV
is
on. (After a few seconds, a window
appears with sound.)
mm
• The initial setup starts when the
lV
powers on for the first time.
If
the
lV
has
been turned on before, the
EZ
Setup will not be invoked. See page 24 for
performing
EZ
Setup from the Setup menu.
Press POWER on the
N,
or TV POWER on the remote control unit
again to turn the power off.
• The
lV
enters standby and the image on the screen disappears.
• The POWER indicator on the
lV
turns off.
mm
•
If
you are not going to use this
lV
for a long period of time, be sure to remove
the AC cord from the AC outlet.
• Weak electric power
is
still consumed even when the
lV
is
turned off.
Initial Setup
When you turn on the N for the first time,
it
will
automatically memorize the broadcasting channels
available
in
the region where you
live.
Perform the
following steps before you press TV POWER on the
remote control unit.
1. Insert the batteries into the remote control unit.
(See
page
8.)
2. Connect the antenna cable to the
lV.
(See page 12.)
3. Plug
in
the AC cord to the AC outlet. (See page
7.)
1
\
'OZE
~
MOU
II
\
J~~o·1
Language (Language setting)
Select from among 3 languages: English, French and Spanish.
1 Press JIt./T
to
select the desired language listed on the
screen, and then press
ENTER.
TV Location
Select "Home"
or
"Store" for the location where you plan to
install the
lV.
2 Press
....
/~
to select "Home" or "Store".
Press
ENTER
to
enter the setting.
Example
mm
•
If
you select "Home", AV MODE
is
set to "STANDARD".
•
If
you select "Store",
AV
MODE
is
set to "DYNAMIC (Fixed)".
In
case
no
remote control signal
is
received within 30 minutes,
AV
MODE will change to "DYNAMIC
(Fixed)"
automatically.
• For changing the
lV
Location after the setting, see "EZ
Setup" on page 24.
Air/Cable (Antenna setting)
Make sure what kind
of
connection
is
made with your
lV
when selecting "Air" or "Cable".
3 Press
....
/~
to
select "Air"
or
"Cable".
Press
ENTER to enter the setting.
Example
CH
Search (Channel search)
Channel auto search makes the
lV
look for
all
channels
viewable
in
the set area.
4 When "Air" is selected
in
Antenna setting:
Press
....
/~
to select "Start", and then press ENTER.
When "Cable"
is
selected
in
Antenna setting:
Press
J/i..lT
to select "Analog & Digital Search Start" to
search both analog and digital broadcasts, or to select
"Analog Search Start" to search only analog broadcasts,
and then press
ENTER.
• The Channel search will start automatically.
• To exit the Channel search screen, select "Cancel", and
then press
ENTER.
mm
•
If
no channel
is
found, confirm the type of connection made
with your
lV
and try
EZ
Setup again.
(See
page 24.)
@-15
To Next Page
Loading...
