Other Viewing Options
•
Presetting
Remote
Control
Function
Operating
the
Connected
Equipment
AQuas
To operate the connected equipment, press
FUNCTION
to
select the
LED
for your device.
(VCR,
AUDIO,
CBUSAT
(cable converter) or DVD.) The
LED
lights up, and the remote control unit button will
function as follows.
• When you operate VCR
or
DVD,
press INPUT
to
select the
terminal connected to your device.
• CABLE and SAT cannot be selected at the same time.
1 SOURCE POWER
• Turns the connected equipment power on and off.
2 ......
• Rewinds the tape and allows picture search.
(VCR)
• Hold
down
to
go
in
reverse.
(DVD)
3 REC
• Starts recording.
(VCR)
4~
• Pressing quickly once takes you to the start of the chapter
currently playing. Each time you press
it,
you move
back
to the start of the previous chapter.
(DVD)
50-9
(CBUSAT), •
(DOT)
(SAT)
• Press a button (or buttons) that corresponds
to
the
channel that you wish
to
watch.
6~
• Starts playback.
(VCR,
DVD)
7~~
• Rapidly advances the tape and allows picture search.
(VCR)
• Hold
down
to fast forward.
(DVD)
811
• Sets pauses and still pictures.
(VCR,
DVD)
9.
• Stops the tape transport.
(VCR)
• Playback stops when pressed. With some DVD players,
pressing the button twice may open the disc tray.
(DVD)
10
~
• Pressing quickly once takes you to the start of the next
chapter. Each time you press it, you move ahead
to
the
start
of
the next chapter.
(DVD)
11
FLASHBACK
• Press
to
switch between the current channel and the
channel you were watching immediately before. Some
manufacturers
do
not preset FLASHBACK. (CBL)
12
CH/\/V
• Press CHI\. or
CHV
to tune
in
to a higher or lower
channel. (CBL)
• Press to select the channel
of
the TV tuner on the VCR.
(VCR)
13
MENU
• When this button
is
pressed, the DVD menu will display.
14
.1.
I
/~,
ENTER
•
./T
I
/~:
Press the button to select items on the SAT
GUIDE screen
or
SAT MENU screen. (SAl). Press the
button
to
select items on the DVD MENU screen.
(DVD)
• ENTER: Press
to
activate the selected function.
(SAT,
DVD)
TV TV
VCR
AUDIO
goo
0
t/tP
CBL/SAT
OVO
FUNCTION
,0
0 0 •
SOURCE
LIGHT
1
II
•
•
rn
6
2
•
•
•
II
7
II
REC
II
3
II
•
•
II
8
4
II
9
I
10
I
5
I
I
I
11
II
VOL
CH
SURROUND(J
I MUTE
I
12
o - 0
MENU
II
13
14
4 After registering the code, the
LED
will stop blinking
then turn off after one second.
(If
you perform
an
incorrect operation, the
LED
will blink quickly then
turn off.)
2 After the
LED
for your device lights up, press
FUNCTION and
DISPLAY
at the same time
to
enter the code registration mode. The
LED
will
blink.
3 Press
0-9
to enter the manufacturer code.
(See
page 34.)
• Preset mode
is
finished once the LED no longer lights
up.
Presetting
manufacturer
codes
1 Press FUNCTION until the
LED
for your device
lights up.
You can operate the connected
AV
products
(AV
receiver, cable box, SAT tuner,
DTV,
VCR,
DVD,
LD)
using the presetting manufacturer function of your
remote control unit.
@-
33
To Next Page
Loading...
