AR-M256/M257/M258/M316/M317/M318/5625/5631 SPECIFICATIONS 3 - 4
: '07/Oct/15
1
F. Fusing
G. Drive
4. Additional functions, copy functions,
and expanded functions
5. Safety and environmental protection
standards
(1) Safety standards
(2) Ozone level
Developing Dry, 2-component magnetic brush
development
Separation (–) DC scorotron
Discharge —
Cleaning Contacted blade
Type Heat roller
Lamp Type Halogen lamp
Voltage 100V: 110V/ 120V to 127V
200V: 220V to 240V
Power
consumption
Main : 650W
Sub : 550W
Fusing temperature 185° (600 dpi)
Heat roller Teflon coated roller
Pressure roller Silicone rubber roller with re-engerized
cube
Separation system Natural separation (with pawl)
Drive section Motor
Main motor DC brushless motor
APS (Automatic
paper selection)
Ye s
(No for APS by flow scan with the RSPF)
AMS (Automatic
magnification ratio
selection)
Ye s
(No for AMS by flow scan with the RSPF)
Stream feeding mode Yes
Job build function Yes (Copy/ Scan)
Auto tray switching Yes (No for manual paper feed)
Memory copy Yes (1 page memory provided as standard)
Rotation copy Yes
E-sort Yes
XY zoom Yes
When the OC is used: Landscape/ Portrait
25 – 400%
When the RSPF is used: Landscape/ Portrait
50 – 200%
1 set 2 copy Yes (No for enlargement)
Binding margin Yes
Default AB series: 0 – 20 mm (Unit of 1 mm)
Inch series: 0 – 1 inch (Unit of 1/ 8 inch)
Edge erase Yes
Default AB series: 0 – 20 mm (Unit of 1 mm)
Inch series: 0 – 1 inch (Unit of 1/ 8 inch)
Center frame erase Yes
Default AB series: 0 – 20 mm (Unit of 1 mm)
Inch series: 0 – 1 inch (Unit of 1/ 8 inch)
Booklet copy No
White/ black reversion Yes
Whole surface only
(Can be inhibited with the simulation.)
2 in 1/ 4 in 1 Yes (Centering provided)
Sorter Yes
Offset function (shifter or finisher) required
Mix paper feed Yes (Only when this function is set)
Preheating Yes (Conditions are set with the key operator
program.)
Auto power shut off
function
Yes (Conditions are set with the key operator
program.)
Message display Yes
Key operator program Yes
Printer status monitor/
Printer administration
utility
Yes (A PCL printer board is required (TCP/
IP only). To use another protocol, an NIC
card is required.)
Wireless LAN support Yes (A 3rd party part is recommended.)
Coin vendor support Yes (Option only for the models for dealers)
Auditor support Yes
Duplex Yes (Standard)
Total counter Yes
Toner save Yes
Department
management
Yes (100 departments)
Job registration/ call Yes (10 jobs)
Cover paper Yes (Insertion and stapling must be allowed
from manual feed.)
OHP insert paper No
Self print function Yes (The service simulations in the machine
and the key operation list are printed.)
Built-in clock Yes
Paper exit tray
selection
(When the finisher is installed)
Machine: Copy/ FAX/ *Printer
Top tray: Copy/ *FAX
Offset tray: Printer/ *Copy
(When the job separator is installed)
Machine: *Copy/ Printer/ FAX
Job separator tray: Copy/ *Printer/ *FAX
* Default: (The above setup items for each
paper exit tray can be changed by the user.)
1 page memory 48MB
North America China
Standard Europe
(Western/North)
UL60950-1
CSA C22.2
No.60950-1-03
21CFR (Laser)
FCC Class Part 15
Class A
ICES-003 Class A
FCC Part 68
ICCS-03
GB4943
GB9254 Class A
GB17625.1
GB/T3382.1
GB/T3382.2
YD/T514, YD/T589,
YD/T703, YD/T965,
YD/T993
IEC60950-1
IEC60825-1 (Laser)
EN60950-1
EN55022 Class A
CISPR22 Class A
EN55024
EN61000-3-2
EN61000-3-3
TS103021 or TBR21
EG201120
EG201121
Australia Taiwan
IEC60950-1
IEC60825-1 (Laser)
AS/NZS 60950
(FAX option)
AS/NZS CISPR 22
Class A
AS/ACIFS0002
AS/NZS60950
CNS14336
CNS13438 Class B
PSTN01
Ozone Less than 0.02mg/m³
Dust Less than 0.075mg/m³
1
To Next Page
Loading...
Need help?
General
