Sharp GF-800Z User Manual

ERASING RECORDED TAPES
Previously recorded materials will be erased automatically
whenever new materials are re-recorded onto the tape. If it
is desired to erase a previously recorded tape without record-
ing over it, follow the instructions below.
• Check to ensure that Deck 1 is out of operation.
• Do not connect any microphones to the EXT MIC sockets.
| Load a tape to be erased into the cassette compartment of
Deck 2.
2 Press the TAPE button of the FUNCTION selector.
3 Press the button. This will automatically
engage the button and begin erasing the tape.
DUBBING FROM DECK 1 TO DECK 2
• Normal speed dubbing as well as high-speed dubbing may
be performed with this unit.
Load a pre-recorded cassette tape into the cassette compart-
ment of Deck 1, and a cassette tape to be recorded into the
cassette compartment of Deck 2.
Set the TAPE selectors of Deck 1 and Deck 2 to their
proper positions (refer to instructions on page 11).
• Do not connect any microphones to the EXT MIC sockets.
Set the CONT PLAY switch to the [1] &/or [2]position.
Press the TAPE button of the FUNCTION selector.
Set the DUBBING SPEED selector to either the
NORMAL or HIGH speed position.
The NORMAL position permits to dub at the normal
speed.
The HIGH position permits to dub at twice the normal
speed.
• Do not change the setting of the DUBBING SPEED
selector during dubbing.
Press the DUBBING START button. The button
of Deck 1, button and button of
Deck 2 are automatically pressed.
For rest of the operations, refer to the recording section on
the previous page.
DUBBING WITH APLD AND APPS FUNCTIONS
Certain selected materials can be dubbed by using the APLD
or APPS function to locate each desired selection.
| Perform steps 1 - 3 of DUBBING FROM DECK 1 TO
DECK 2 to prepare the unit for dubbing.
2 Locate the beginning of the desired selection by using the
APLD (refer to page 13).
3 Set the desired number of selections to be dubbed with
the SET button (refer to instructions for APPS OPERA-
TION on page 13).
4 Press the DUBBING START button.
5 Upon conclusion of dubbing of the preset selections, the
tapes on Deck 1 and Deck 2 will simultaneously stop and
the END PAUSE indicator illuminates.
6 Press the button of Deck 1 and 2.
7 To perform dubbing of subsequent selections, repeat
Steps 1 - 6.
16

Sharp GF-800Z Specifications

Power

AC power source voltage	110V - 127V and 220 - 240V
DC power source voltage	15V
Frequency	50/60Hz

Output Power

PMPO output power	52W (26W + 26W)
MPO output power	40W (20W + 20W)
RMS output power	26W (13W + 13W)

Tape Recorder Specifications

frequency response for normal tape	30Hz — 14, 000Hz
frequency response for CrO2 tape	30Hz - 16, 000Hz
frequency response for metal tape	30Hz - 17, 000Hz
signal/noise ratio for Deck 1 playback	55 dB
signal/noise ratio for Deck 2 recording	50 dB

Impedance

external mic input impedance	600 ohms
phono/line in input impedance	50 kohms/50 kohms
loaded impedance for headphones	8 ohms — 32 ohms
loaded impedance for external speakers	8 ohms — 16 ohms
line out impedance	0.6V/50 kohms

Radio Specifications

AM frequency range	526.5 kHz - 1606.5 kHz
SW1 frequency range	2.3 MHz - 7.3 MHz
SW2 frequency range	7.3 MHz - 22 MHz
FM frequency range	87.6 MHz - 108 MHz

Speaker Specifications

woofer size	16 cm (6-1/2")
tweeter count	2
speaker impedance	8 ohms
maximum input	26W

Weight and Dimensions

width	681 mm (26-13/16")
height	225 mm (8-7/8")
depth	210 mm (8-1/4")
weight	8.8 kg (19.4 lbs.) without batteries