EasyManuals Logo

Sharp LC-52XS1E Service Manual

Sharp LC-52XS1E
172 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #73 background imageLoading...
Page #73 background image
LC-52XS1E/RU/LC-65XS1E/RU
5 – 14
19.IC7002 (RH-iXC331WJQZQ)
This is a monitor microprocessor, which receives the remote control light, controls the CEC signal, detects the keys, and detects the OPC. It also
detects the errors relating to the power supply within the IF PWB and controls the power supply of the monitor.
20.IC7006 (VHiBR24L04F-1Y)
This is an EEPROM, in which the portion of the data processed by IC7002 is stored.
21.IC5802 (VHiLTC1154+-1Y)
This is a power supply IC, which supplies 5V for the optional wireless transmission unit. It also detects short circuits and has the thermal shutdown
function.
22.IC5901 (VHiBD9045FV-1Y)
This is a DC/DC converter, which inputs 15V from the power supply unit and generates 5V and 3.3V used within the IF PWB.
2ch DC/DC Converter
27 MODE2 I Distribution, DDR function enable.
The use of these multi-function depends on the setting of MODE<1:0>.
MODE<1:0>=HH(Single-in/Single-out Mode)
H: Distribution function enable.
L: Distribution function disable.
MODE<1:0>=HL(Single-in/Single-out Mode)
H: DDR (Double Edge input) function enable.
L: DDR (Double Edge input) function disable.
30 /PDWN I H: Normal operation,
L: Power down (all outputs are Hi-Z)
31 PRBS I PRBS generator is active when MODE <1:0> = LL (Dual-in/Dual-out mode)
H: PRBS generator is enable. Pattern is PRBS-23.
L: Normal Operation
10, 11, 12, 16,
28, 32
Reserved I Must be tied to GND.
23 Reserved I Must be Open.
29, 33, 109 N/C Must be Open.
3, 13, 82, 93,
104, 113, 125,
137
VCC - Power Supply Pins for TTL inputs, output and digital circuitry.
4, 14, 83, 94,
105, 114, 126,
138
GND - Ground Pins for TTL inputs, outputs and digital circuitry.
43, 49, 55, 61,
67
LVCC - Power Supply Pins for LVDS Outputs.
37, 42, 48, 54,
60, 66, 72
LGND - Ground Pins for LVDS Outputs.
35, 74 PVCC - Power Supply for PLL circuitry.
34, 36, 73, 75 PGND - Ground Pin for PLL circuitry.
Pin No. Pin Name I/O Pin Function
1 OUTL2 O Low side FET gate drive terminal 2
2 DGND2 - Low side FET source terminal 2
3 SW2 I High side FET source terminal 2
4 OUTH2 O High side FET gate drive terminal 2
5 BOOT2 - OUTH2 driver power supply terminal
6 CL2 I Over-current detection setting terminal 2
7 N.C. - No Connection
8 VREG5 - The REG output for FET drive
9 CL1 I Over-current detection setting terminal 1
10 BOOT1 - OUTH1 driver power supply terminal
11 OUTH1 O High Side FET gate drive terminal 1
12 SW1 I High Side FET source terminal 1
13 DGND1 - Low side FET source terminal 1
14 OUTL1 O Low side FET gate drive terminal 1
15 GND - Ground terminal
16 TM1 - Output 1 OCP and an OVP timer latch setting terminal
17 SS1 - Soft starting time setting terminal 1
Pin No. Pin Name I/O Pin Function

Other manuals for Sharp LC-52XS1E

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Sharp LC-52XS1E and is the answer not in the manual?

Sharp LC-52XS1E Specifications

General IconGeneral
BrandSharp
ModelLC-52XS1E
CategoryLCD TV
LanguageEnglish

Related product manuals