Sharp MX-4101N

MX-5001N SIMULATION 6 – 138
67-34
Purpose
Adjustment/Setup
Function (Purpose)
Used to set the density correction in the
printer high density section. (Support for
the high density section tone gap)
Section
Printer
Operation/Procedure
1) Enter the set value with 10-key.
2) Press [OK] key. (The set value is saved.)
• When tone gap is generated in the high density section, set items
A and B to "0."
The density in the high density section is decreased, but tone
gap is reduced.
• To increase the density in the high density section further, set
items A and B to "1.
The tone gap may occur in high density part.
NOTE: Do not change the values of items C, D, E, and F. If these
values are changed, the density in the high density area is
changed.
67-36
Purpose
Adjustment/Setup
Function (Purpose)
Used to adjust the density in the low den-
sity section.
Section
Printer
Operation/Procedure
1) Enter the adjustment value using the 10-key.
2) Press [OK] key.
When the adjustment value is increased, the low density images
are strongly reduced. When the adjustment value is decreased, the
low density are images are weakly reproduced.
When tone gap is generated in the low density section (highlight
section), changing this adjustment value may improve the trouble.
67-52
Purpose
Adjustment/Setup
Function (Purpose)
Used to set the default of the gamma of the
printer screen. (for PCL/PS)
Section
Printer
Operation/Procedure
1) Select a target default setting mode with the touch panel.
Press [ALL] key to select all the modes.
2) Press [EXECUTE] key and press [YES] key.
When the printer screen gamma was changed by SIM 67-33, it is
reset to the default.
0 Enable
1 Disable
Item/Display Content
Setting
range
Default
value
ACMY
(0: ENABLE
1: DISABLE)
0 CMY engine highest
density correction
mode : Enable
0 - 1 0
1 CMY engine highest
density correction
mode : Disable
BK
(0: ENABLE
1: DISABLE)
0 K engine highest
density correction
mode : Enable
0 - 1 1
1 K engine highest
density correction
mode : Disable
C CYAN MAX
TARGET
Scanner target value for
CYAN maximum density
correction
0 - 999 500
D MAGENTA MAX
TARGET
Scanner target value for
MAGENTA maximum
density correction
0 - 999 500
E YELLOW MAX
TARGET
Scanner target value for
YELLOW maximum
density correction
0 - 999 500
FBLACK MAX
TARGET
Scanner target value for
BLACK maximum density
correction
0 - 999 500
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1*,1(0$;,080'(16,7<$'-8670(1702'()2535,17(5


$˖
˷˹
˖&0<(1$%/(',6$%/(
$˖
˖.(1$%/(',6$%/(
%˖
˖&<$10$;7$5*(7
&˖
˖0$*(17$0$;7$5*(7
'˖
˖%/$&.0$;7$5*(7
)˖
˖<(//2:0$;7$5*(7
(˖
2.
Item/Display Content
Screen HEAVYPAPER Heavy paper screen
1200DPI_1BIT SCREEN5(1200dpi 1bit Photo)
SCREEN6(1200dpi 1bit Graphics)
600DPI_1BIT SCREEN1(600dpi 1bit Photo)
SCREEN2(600dpi 1bit Graphics)
B/W SCREEN7(B/W 600dpi 1bit)
SCREEN8(B/W 600dpi 4bit)
SCREEN9(B/W 1200dpi 1bit)
SCREEN10(Toner Save B/W)
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
35,17(5+,*+/,*+7$'-8670(17


$˖
˷˹
˖$3$7&+,1387
$˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
35,17(5&$/,%5$7,21'$7$&/($5$7',7+(53&/


+($9<3$3(5 '3,B%,7 %:'3,B%,7
$//
$5(<28685("
<(6 12 (;(&87(


