MX-M350/M450 N/U SIMULATION 9 - 32
Operation/Procedure
1) Open the manual paper feed guide to the max. width.
2) Select MAX POSITION with 10-key.
3) Press [START] key.
The max. width detection level is recognized.
4) Press [SYSTEM SETTINGS] key.
5) Set the manual paper feed guide to A4R size width.
6) Select POSITION with 10-key.
7) Press [START] key.
The A4R width detection level is recognized.
8) Press [SYSTEM SETTINGS] key.
9) Set the manual paper feed guide to A5/A5R size width.
10) Select POSITION2 with 10-key.
11) Press [START] key.
The A5R width detection level is recognized.
12) Press [SYSTEM SETTINGS] key.
13) Open the manual paper feed guide to the min. width.
14) Select MIN POSITION with 10-key.
15) Press [START] key.
The min. width detection level is recognized.
If the above procedures are not completed normally, "ERROR" is
displayed. If completed normally, "COMPLETE" is displayed.
Operation/Procedure
1) Select the number corresponding to the set item with 10-key.
2) Press [START] key.
3) Enter the set value with 10-key.
4) Press [START] key.
Operation/Procedure
The operating conditions of sensors and detectors are displayed.
The active sensors and detectors are highlighted.
The paper width detection level is also displayed.
40-2
Purpose Adjustment
Function
(Purpose)
Used to adjust the manual paper feed tray paper
width detector detection level.
Section Paper feed
Item Operation
Select 4 and press [START] key. Press [SYSTEM SETTINGS] key.
SIMULATION 40-2
BYPASS TRAY ADJUSTMENT. SELECT 1-4, AND PRESS START.
1. MAX. POSITION
2. POSITION 1
3. POSITION 2
4. MIN. POSITION
1
SIMULATION 40-2
BYPASS TRAY ADJUSTMENT.
MAX. POSITION ··· COMPLETE (or "ERROR")
Press [SYSTEM SETTINGS] key.
SIMULATION 40-2
BYPASS TRAY ADJUSTMENT.
POSITION 1 ··· COMPLETE (or "ERROR")
Select 1 and press [START] key.
SIMULATION 40-2
BYPASS TRAY ADJUSTMENT.
POSITION 2 ··· COMPLETE (or "ERROR")
Press [SYSTEM SETTINGS] key.
Press [SYSTEM SETTINGS] key.
Select 2 and press [START] key.
Select 3 and press [START] key.
SIMULATION 40-2
BYPASS TRAY ADJUSTMENT.
MIN. POSITION ··· COMPLETE (or "ERROR")
40-7
Purpose Adjustment/Setup
Function
(Purpose)
Used to enter the manual paper feed tray paper
width adjustment value.
Section Paper feed
Item Operation
1 MAX. POSITION Max. width
2 POSITION 1 Adjustment point 1
3 POSITION 2 Adjustment point 2
4 MIN. POSITION Min. value
Press [START] key. Press [SYSTEM SETTINGS] key.
40-11
Purpose Operation test/Check
Function
(Purpose)
Used to check the multi-purpose tray width detec-
tion level.
Section Paper feed
Item Operation
MCSS1 Tray 3 size detection 1
MCSS2 Tray 3 size detection 2
MCSS3 Tray 3 detection size 3
MCSS4 Tray 3 size detection 4
Multi Purpose
Tr ay
(MPT width direction detection size is
displayed.) A4/A3, 11X, B5/B4, 8.5X, A4R,
B5R, A5R, 5.5X, 7.25X, EXTRA
SIMULATION 40-7
1
BYPASS TRAY VALUE SETTING. SELECT 1-4, AND PRESS START.
1. MAX. POSITION : 66
2. POSITION 1 : 447
3. POSITION 2 : 704
4. MIN. POSITION : 916
SIMULATION 40-7
BYPASS TRAY VALUE SETTING. INPUT VALUE 0-1023, AND PRESS
START.
1. MAX. POSITION
66
SIMULATION 40-11
TRAY3 SENSOR CHECK..
MCSS1 MCSS2 MCSS3 MCSS4
(Multi Purpose Tray width size: A4/A3)
To Next Page
Loading...
