Sharp MX-M350 - Page 178

MX-M350/M450 N/U SIMULATION 9 - 39
Operation/Procedure
1) Select the adjustment item of FAX EXP. LEVEL with 10-key.
2) Press [START] key.
3) Enter the print density level with 10-key.
4) Press [P] key or [START] key.
The adjustment value is set.
When [START] key is pressed, printing is perfumed and the
adjustment value is set simultaneously.
Check the density of printed image.
NOTE: When the FAX print image density is adjusted with this sim-
ulation, the print image densities of all the FAX modes are
changed to the image density level set with this simulation.
That is, the print image density of each FAX mode set with
SIM 46-13, 14, 15 is changed to the print image density
level adjusted with this simulation.
To select paper (paper feed tray), perform the following proce-
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray to be
used with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
NOTE: When [P] key is pressed after entering an adjustment value
in this simulation, the adjustment value is set. When
START key is pressed, the adjustment value is set and
copying is performed.
Select 2, and press [START] key. Press [START] key, or
press [SYSTEM SETTINGS] key.
46-12
Purpose Adjustment
Function
(Purpose)
Used to adjust the print density in the FAX mode
(all modes).
Item Picture quality
Item
Set
range
Default
0 TRAY SELECT Paper feed tray selection
1 COPY START Copy START (Default)
2 FAX EXP. LEVEL FAX mode print density 0 - 99 50
SIMULATION 46-11
Select other than 0 - 2, and
press [START] key.
Press [SYSTEM SETTINGS] key.
SIMULATION 46-11
EXP. LEVEL SETUP (PHOTO2). INPUT VALUE 0-99, AND PRESS
START.
3. 1.0
Press [START] key.
SIMULATION 46-11
EXP. LEVEL SETUP (PHOTO2). NOW COPYING.
50
Press [SYSTEM SETTINGS] key,
or terminate copying.
SIMULATION 46-11
EXP. LEVEL SETUP (PHOTO2). SELECT 1-5, AND PRESS START.
(FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
5. BPT
Press [START] key,
or press [SYSTEM SETTINGS] key.
1
Select 0, and
press [START] key.
1
Select 1,
and press
[START] key.
EXP. LEVEL SETUP (PHOTO2). SELECT 0-11, AND PRESS START.
0. TRAY SELECT 1 1. COPY START
2. EXP LEVEL 1
3. 1.0 50 4. 1.5 50 5. 2.0 50
6. 2.5 50 7. 3.0 50 8. 3.5 50
9. 4.0 50 10. 4.5 50 11. 5.0 50
SIMULATION 46-11
EXP. LEVEL SETUP (PHOTO2). SELECT 3-11, AND PRESS START.
(EXP. LEVEL SELECT)
3. 1.0 4. 1.5 5. 2.0
6. 2.5 7. 3.0 8. 3.5
9. 4.0 10. 4.5 11. 5.0
1
Normal display NOW PRINTING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
1TRAY1 TRAY1
2TRAY2 TRAY2
3TRAY3 TRAY3
4TRAY4 TRAY4
5 BPT Manual feed
Select 0, and
press [START] key.
Press [START] key, or
press [SYSTEM SETTINGS] key.
SIMULATION 46-12
EXP.LEVEL SETUP FAX(AUTO SET). SELECT 0-2, AND PRESS
START.
0.TRAY SELECT 1 1.COPY START
2.FAX EXP.LEVEL 50
Press [SYSTEM SETTINGS] key.
SIMULATION 46-12
EXP.LEVEL SETUP FAX(AUTO SET), INPUT VALUE 0-99, AND
PRESS START.
2.FAX EXP.LEVEL
50
1
Press [START] key.
Press [SYSTEM SETTINGS] key,
or terminate copying.
SIMULATION 46-12
EXP.LEVEL SETUP FAX(AUTO SET). NOW PRINTING.
Select 1, and
press [START] key.
Select other than 0 - 1, and
press [START] key.
SIMULATION 46-12
EXP.LEVEL SETUP FAX(AUTO SET).SELECT 1-5, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT