Sharp MX-M350 - Page 211

MX-M350/M450 N/U SIMULATION 9 - 72
❏: Error diffusion process
Note*: Since the "DENSITY" of an actual copy or printer output
differs, they differ from the output of self print.
58 ❍ All surface 1 by 5 (Vertical)
59 ❍ All surface 1 by 5 (Horizontal)
60 ❍ All surface 2 by 2 (Vertical)
61 ❍ All surface 2 by 2 (Horizontal)
62 ❍ All surface 2 by 3 (Vertical)
63 ❍ All surface 2 by 3 (Horizontal)
64 ❍ All background
65 ❍ Special pattern
66 ❏ For every other 1 block width
128 pixels/ 32 gradations
67 ❏ For every other 1 block width
128 pixels/ 16 gradations
68 ❏ For every other 1 block width
128 pixels/ 8 gradations
69 ❍ 1-dot pattern
70 ❍ Print adjustment pattern with
scale (Vertical)
71 ❍ Grid pattern
72 ❍ Slant line 45 degrees
73 ❍ Slant line 26.6 degrees
74 ❍ Slant line 63.4 degrees
75 ❍ ID/BG pattern
76 ❍ Dot pattern 12.5%
77 ❍ Dot pattern 28%
78 ❍ Dot pattern 50%
79 ❏ All surface effort diffusion
background
80 ❍ All surface dither process
background
81 ❍ For every other 1 block width
128 pixels/ 32 gradations
82 ❍ For every other 1 block width
128 pixels/ 16 gradations
83 ❍ For every other 1 block width
128 pixels/ 8 gradations
84 ❍ Memory check pattern
85 ❍ Cleaning check pattern
86 ❍ Offset check pattern
87 ❍ Text pattern A Note *
88 ❍ Text pattern B Note *
89 ❍ Text pattern C Note *
90 Toner quantity measuring chart
91 Radiation chart
98 Data printing
No
Engine
pattern
Controller Pattern Note
Select 1, and
press [START] key.
Select other than 1, and
press [START] key.
Press [START] key, or
press [SYSTEM SETTINGS] key.
SIMULATION 64-1
SELF PRINT MODE. SELECT 0-7, AND PRESS START.
0. TRAY SELECT :1 1. PRINT START
2. PRINT PATTERN:87 3. DENSITY :1
4. MULTI : 1 5. MODE :1
6. LEVEL : 1 7. DUPLEX :1
1
SIMULATION 64-1
SELF PRINT MODE. INPUT VALUE, AND PRESS START.
(PRINT PATTERN)
INPUT 1-98.
71
SIMULATION 64-1
SELF PRINT MODE. INPUT VALUE, AND PRESS START.
(DENSITY)
1-255
100
SIMULATION 64-1
SELF PRINT MODE. INPUT VALUE, AND PRESS START.
(MULTI COUNT)
1-999
1
SIMULATION 64-1
SELF PRINT MODE. SELECT 1-8, AND PRESS START.
(MODE)
1.STANDARD 2.SMOOTHING 3.TONER SAVE 4.HALF TONE
5.SMOOTHING+ TONER SAVE 6.SMOOTHING+ HALF TONE
7.TONER SAVE+ HALF TONE
8.SMOOTHING+ TONER SAVE+ HALF TONE
1
3
SIMULATION 64-1
SELF PRINT MODE. SELECT 1-5, AND PRESS START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 5.BPT
1
SIMULATION 64-1
SELF PRINT MODE. SELECT 1-2, AND PRESS START.
(DUPLEX)
1.NO 2.YES
1
SIMULATION 64-1
SELFT PRINT MODE.. EXECUTING···
0. TRAY SELECT :1
2. PRINT PATTERN:87 3. DENSITY :1
4. MULTI : 1 5. MODE :1
6. LEVEL : 1 7. DUPLEX :1
0
(3)
(2)
(4)
(5)
(6)
(0)
(7)
SIMULATION 64-1
SELF PRINT MODE. INPUT VALUE, AND PRESS START.
(LEVEL)
1-5