2
Contents
Request ................................................................ 1
Preface .................................................................. 1
1. Safety rules ...................................................... 3
2. Introduction ...................................................... 4
2-1. Preliminary check ................................................. 4
(1) Model code check ................................................................ 4
(2) Accessories check ............................................................... 4
2-2. Notes on use ........................................................ 4
3. Installation and wiring ..................................... 4
3-1. Installation site (environmental conditions) .......... 4
3-2. Mounting ............................................................... 4
3-3. External dimensions and panel cutout ................. 5
3-4. Wiring ................................................................... 6
3-5. Terminal layout ..................................................... 6
3-6. Terminal arrangement table ................................. 6
3-7. Operation preparations ......................................... 7
4. Names and functions of parts on front panel 8
5. Parameter diagram and setting ...................... 9
5-1. Parameter diagram ............................................... 9
5-2. Display when power is applied ........................... 10
5-3. Switching screens .............................................. 10
(1) Switching screens within screen group 0 .......................... 10
(2) Switching between screen group 0 and screen group 1.... 10
(3) Switching screens within screen group 1 .......................... 10
(4) Switching to screen group 2 .............................................. 10
(5) Switching screens within screen group 2 .......................... 11
(6) Switching to screen group 3 .............................................. 11
(7) Switching screens within screen group 3 .......................... 11
(8) Switching to screen group 4 .............................................. 11
(9) Switching screens within screen group 4 .......................... 11
(10) Switching to screen group 5 ............................................ 11
(11) Switching screens within screen group 5 ........................ 11
(12) Set data modification ....................................................... 12
5-4. Auto return function ............................................ 12
5-5. Screen group 0 setting ....................................... 12
(1) Setting target set values (SV) ............................................ 12
(2) Manual setting of control output ........................................ 12
(3) Auto tuning (AT) ................................................................ 13
(4) Reset (RST)/run (RUN) ..................................................... 13
(5) Event setting ...................................................................... 14
(6) Multi SV (target set values) ............................................... 14
6. Screen explanation and setting items ......... 15
7. Measuring range codes ................................. 21
8. Explanation of functions ............................... 22
8-1. Events ................................................................. 22
(1) Alarm action ....................................................................... 22
(2) Event standby action selection .......................................... 22
(3) Event selection alarm action diagrams .............................. 22
(4) Control output inverted output ........................................... 23
(5) Event status output action ................................................. 23
8-2. P.I.D. ................................................................... 23
(1) P (proportional action) ....................................................... 23
(2) I (integral time) ................................................................... 23
(3) D (derivative time) ............................................................. 23
(4) MR (manual reset) ............................................................. 23
(5) SF (target value function) .................................................. 23
8-3. Control output ...................................................... 24
(1) Lower limit and higher limit limiter setting .......................... 24
(2) Proportional cycle .............................................................. 24
(3) Control output characteristics ............................................ 24
(4) Two-position action ............................................................ 24
8-4. External control input (DI).................................... 25
(1) Controller action execution (RUN1) ................................... 25
(2) Controller action execution (RUN2) ................................... 25
(3) Manual output (MAN) ........................................................ 25
(4) Auto tuning execution (AT) ................................................ 25
(5) SV selection (SV) .............................................................. 25
(6) Output characteristic (ACT) ............................................... 25
(7) Program (PROG) ............................................................... 25
(8) Hold signal (HLD) .............................................................. 25
(9) Advance (ADV) .................................................................. 25
(10) Total unlatching (L_RS) ................................................... 25
8-5. Change in position of decimal point .................... 26
(1) Change in position of decimal point for linear input ........... 26
(2) Change in position of decimal point of TC/RTD range ...... 26
8-6. Start SV ............................................................... 26
(1) When start SV function is invalid ....................................... 26
(2) When start SV function is valid .......................................... 26
(3) When start SV function is valid and start step is skipped .. 26
8-7. Guarantee soak (GUA)........................................ 27
(1) When OFF ......................................................................... 27
(2) When guarantee soak zone is set ..................................... 27
9. Causes and remedy of trouble and errors ... 28
9-1. Causes and remedy of trouble ............................ 28
9-2. Causes and remedy of errors .............................. 28
(1) Abnormal measured input ................................................. 28
10. Parameter setting record ............................ 29
11. Specifications .............................................. 31
To Next Page
Loading...
Need help?
General
