29
10. Parameter setting record
For the sake of convenience, you should record your settings and selections.
Initial values for code 05 (K) are given here.
Screen No. Parameter (item)/screen Initial value Setting/selection Record
0-0 Basic screen (SV) 0 (h) h
0-1
Standby action (FIX)
Reset action (program)
EXE (~~)
RST ()
~~
0-2 Output monitoring
0-3 Execution step No. monitoring
0-4
Remaining time of step
monitoring
0-5
Number of pattern executions
monitoring
0-6 PID execution monitoring
0-7 Ramp process halt rAmP (|)
0-8 Hold HLd ()
0-9 Advance AdV (|)
0-10 FIX event 1 set value setting E1Hd (~i) jhhh
0-11 FIX event 2 set value setting E2Ld (~j) qqq
0-12 AT action At (|)
0-13 Latching release LAch (|) i
1-0 FIX initial screen FiX () ~
1-1 FIX ON/OFF FiX ()
1-2 SV No. SVNo. () i
1-3 SV1 setting SV1 (i) h
1-4 SV2 setting SV2 (j) h
1-5 Ramp incremental value rP_u (¦)
1-6 Ramp lower limit value rP_d (¦)
1-7 Ramp unit rPun () ~
1-8 Ramp ratio rP_r (¦) i
2-0 Initial screen Pid () ~
2-1 OUT PID1 P P1 (i) uh
2-2 OUT PID1 hysteresis dF1 (i) jh
2-3 OUT PID1 I i1 (i) ijh
2-4 OUT PID1 D d1 (i) kh
2-5 OUT PID1 manual reset mr1 (i) rh
2-6 OUT PID1 target value function SF1 (mi) rlh
2-7 OUT PID1 lower limit limiter o_L1 (¦i) rh
2-8 OUT PID1 higher limit limiter o_H1 (¦i) ihrh
2-9 OUT PID2 P p2 (j) uh
2-10 OUT PID2 hysteresis dF2 (j) jh
2-11 OUT PID2 I i2 (j) ijh
2-12 OUT PID2 D d2 (j) kh
2-13 OUT PID2 manual reset mr2 (j) rh
2-14 OUT PID2 target value function SF2 (mj) rlh
2-15 OUT PID2 lower limit limiter o_L2 (¦j) rh
2-16 OUT PID2 higher limit limiter o_H2 (¦j) ihrh
3-0 Initial screen ProG () ~
3-1 Start SV value StSV () h
3-2 End step End (~) ih
3-3 Number of pattern executions Pcnt () i
3-4 Start mode S_md (¦)
3-5 Guarantee soak GUAZ (|)
3-6 Pattern EV1 level value P1Hd (i) jhhh
3-7 Pattern EV2 level value P2Ld (j) qqq
3-8 Step 1 SV value S_01 (¦hi) h
3-9 Step 1 time t_01 (¦hi) h²hh
3-10 Step 1 PID No. P_01 (¦hi) h
3-11 Step 2 SV value S_02 (¦hj) h
3-12 Step 2 duration t_02 (¦hj) h²hh
3-13 Step 2 PID No. P_02 (¦hj) h
3-14 Step 3 SV value S_03 (¦hk) h
3-15 Step 3 time t_03 (¦hk) h²hh
3-16 Step 3 PID No. P_03 (¦hk) h
3-17 Step 4 SV value S_04 (¦hl) h
3-18 Step 4 time t_04 (¦hl) h²hh
3-19 Step 4 PID No. P_04 (¦hl) h
3-20 Step 5 SV value S_05 (¦hm) h
3-21 Step 5 time t_05 (¦hm) h²hh
3-22 Step 5 PID No. P_05 (¦hm) h
3-23 Step 6 SV value S_06 (¦hn) h
3-24 Step 6 time t_06 (¦hn) h²hh
3-25 Step 6 PID No. P_06 (¦hn) h
To Next Page
Loading...
Need help?
General
