Siemens hicom 150 e

To Next Page

To Previous Page

Installing the Software

After the InstallShield® Wizard has started, the Welcome window

is displayed.

4. Click the Next button to confirm.

You can exit installation at any time by clicking the Cancel

button. Any files that were already copied to your hard disk

are removed.

Main Page

Default Chapter3
- Table of Contents3
Introduction7
- Hicom Attendant P7
- Overview of Features8
- About this Manual9
- Requirements9
- Symbols10
Operating the Hicom Attendant P12
Startup13
User Interface14
- Desktop14
- Attendant Monitor20
- Busy Lamp Field25
- Service Menu30
Answering Calls31
- Answering a Waiting Call (Second Call)33
- Activating/Deactivating the Call Waiting Tone34
- Picking up Calls35
- Activating/Deactivating the Ringer Signal36
- Setting the Volume37
- Actuating the Entrance Telephone Connection/Door Opener38
Terminating a Call39
Dialing40
- Dialing External Calls40
- Dialing Internal Calls41
- Dialing with the Repertory Dial Keys42
- Dialing from the Busy Lamp Field42
- Dialing with Redial44
- Dialing from the Electronic Directory45
Consultation/Transfer/Conference46
- Transferring Calls46
  - Normal Transfer46
  - Speed Transfer48
- Consultation Hold49
- Hold50
  - Placing External Calls on Hold50
  - Placing Internal Calls on Hold51
- Toggle52
- Conference53
- Park54
- Overriding Calls55
- Overriding Do Not Disturb56
- Display Suppression57
Reaching Parties more Effectively58
- Callback58
- Paging60
- Messages61
  - Sending a Message61
  - Receiving a Message62
- Releasing an External Trunk63
- Radio Paging (PSE) (Not for U.S.)64
- Paging a Party64
Forwarding Calls66
Night Answer68
- Entering a Night Destination68
- Selecting a Night Destination70
- Activating Night Answer71
- Deactivating Night Answer71
Notebook72
Call Charges (Not for U.S.)73
Programming/Changing Repdial Keys74
Electronic Directory (ETD)76
- Starting the ETD76
- Searching for a Station77
- Searching on the Basis of Other Station Data78
- Adding New Stations79
- Editing an Entry82
Keyboard Commands84
Emergency Operation86
Installing and Configuring the Hicom Attendant P87
Installing the Hardware88
- System Requirements88
- General Instructions89
- Installing the Hicom Attendant P Via the Optiset E Control/Data Adapter with an Optiset E System Telephone90
- Installing the Hicom Attendant P Via a U P0/EPCI Card with Handset Cradle and Handset91
Installing the Software96
Configuring the Hicom Attendant P102
- Entering Settings102
- Saving the Settings113
- Configuring the Electronic Directory114
  - Starting the ETD114
  - Adding New Stations115
- Backing up the ETD Database118
Error Correction in Hicom Attendant P119
Frequently Asked Questions120
- Do I Have to Configure the U P0/EPCI Card120
- Which PCI Slot Should I Use for the U P0/EPCI Card120
- Is the U P0/EPCI Card Compatible with PCI Spec 2.1120
- Which Interrupt Should I Use for the U P0/EPCI Card120
- Why Won't My Computer Work after I've Installed the U P0/EPCI Card122
Problem Correction124
- The Attendant P Does Not Start Correctly124
- The Attendant P Is no Longer Responding124
- The Message Please Wait - Trunk Error Appears in the System Bar125
- The Busy Lamp Field Is Malfunctioning125
- The Directory no Longer Contains Data125
- Troubleshooting Using the Trace Button (System Administrator Only)126
Index127

Siemens hicom 150 e - Page 97

Table of Contents

Other manuals for Siemens hicom 150 e

Related product manuals