Siemens HiPath 4000 - User Manual

Other manuals for Siemens HiPath 4000

User Guide125 pages

Operation Manual164 pages

Administrator's Manual164 pages

Manual56 pages

Administration Guide125 pages

Operating Manual135 pages

User Manual63 pages

Quick Reference Card2 pages

Quick Reference6 pages

Quick Reference Guide9 pages

Questions and Answers:

Y
ymurilloAug 28, 2025
How to fix 'Base n lashes' error on Siemens HiPath 4000 Telephone?
- M
  Mike JohnsonAug 28, 2025
  If your Siemens Telephone displays the line "Base n" lashes, it could be due to several reasons: * The handset is not registered - register the handset. * The handset is outside the base radio range or the radio signals are too weak - move closer to the base or change your position. * The intervals between synchronization attempts are too long - switch the handset off and then back on again.
A
Ashley ScottAug 28, 2025
What to do if my Siemens Telephone shows 'Feature not avail.'?
- K
  kayla98Aug 28, 2025
  If your Siemens Telephone displays 'Feature not avail.', 'Incorrect entry', or 'Key not programmed', it indicates that a speed dial number is not available, an appointment was entered incorrectly, the entry is blocked or not allowed, a prerequisite has not been fulfilled, or the number dialed was incomplete. Correct your input, select a permitted option, or enter the phone number in full.
T
Thomas HallAug 31, 2025
What does de-crescendo tone sequence mean on Siemens HiPath 4000?
- K
  Kayla HardinSep 1, 2025
  If you hear a de-crescendo tone sequence during input on your Siemens Telephone, it indicates an incorrect entry was made. Repeat the key sequence while watching the display, and consult the operating manual where applicable.
D
Daniel PerezAug 27, 2025
What to do if my Siemens HiPath 4000 says 'Re-enter code:'?
- M
  maydavidAug 27, 2025
  If your Siemens Telephone displays 'Re-enter code:', it means the communication system is overloaded. Please wait and try again later.
K
kathleen34Aug 27, 2025
What to do if my Siemens HiPath 4000 shows 'Time exceeded'?
- P
  Peter DuncanAug 27, 2025
  If your Siemens Telephone displays 'Time exceeded', it means the maximum input time was exceeded because the On-hook key was not pressed, and there were long pauses between keystrokes. To resolve this, avoid long pauses when entering information and press the On-hook key.
M
Michael ThomasAug 27, 2025
Why does my Siemens HiPath 4000 Telephone say 'Connect. No dial tone available'?
- W
  Walter RossAug 27, 2025
  If your Siemens Telephone displays 'Connect. No dial tone available' immediately after pressing the Talk key, it means calls cannot be made because the communication system is currently in use by other users. Please try your call again later.
M
michael92Aug 26, 2025
What to do if my Siemens IP Phone shows 'Base 1 Outgoing and incoming calls and activation/deactivation are not possible'?
- M
  Melissa DeleonAug 26, 2025
  If your Siemens IP Phone shows 'Base 1 Outgoing and incoming calls and activation/deactivation are not possible,' it means that the handset is blocked. To fix this, remove the battery pack from the handset and then re-insert it. Then, proceed as if you were loading batteries for the first time.
B
Brenda RiosAug 26, 2025
What to do if my Siemens IP Phone displays 'Base 1 Outgoing and incoming calls and activation/deactivation are not possible'?
- C
  Christopher NorrisAug 26, 2025
  If you see the following on your Siemens IP Phone: 'Base 1 Outgoing and incoming calls and activation/deactivation are not possible', it means that the handset is locked. Remove the batteries from the handset and then re-insert them, proceeding as you would when loading batteries for the first time.
J
jacksoncruzAug 25, 2025
What to do if the line 'Base n' flashes on my Siemens IP Phone?
- W
  william55Aug 26, 2025
  If your Siemens IP Phone displays 'Base n' flashing, it indicates the handset is likely out of the base radio range, the radio signals are too weak, the handset isn't registered, or synchronization attempts are too spaced out. Try moving closer to the base, changing your position, registering the handset, or switching the handset off and on again.
M
Matthew WoodsAug 25, 2025
What to do if Siemens Handsets has no reaction to key-stroke?
- M
  Michael SmithAug 25, 2025
  If your Siemens Handsets does not react when you press a key, it's likely that the keypad lock is activated. To unlock it, press the hash key until you hear a confirmation tone.