How to fix a Siemens Handsets with no display?
If your Siemens Handsets has no display, it could be due to a couple of reasons. The mobile telephone might not be switched on; in this case, press the on-hook key until you hear a confirmation tone. Alternatively, the battery might be empty; in this case, charge or replace the battery and try again.
Why does the line "Base n" flash on my Siemens Handsets?
If your Siemens Handset displays the message "Base n" flashing, it could mean several things. First, you might be out of the base radio range or the radio signal is too weak, so try moving to a different location. Second, the handset might not be registered, so you should register it. Finally, the synchronization attempts might be too far apart, so try switching the handset off and then back on again.
What to do if there is nothing audible during a call on Siemens Handsets?
If you can't hear anything during a call on your Siemens Handsets, it's possible that the microphone and receiver are muted. This can happen if the left side of the control key was pressed accidentally. To fix this, press the "Go Back" display key to re-activate the microphone and the receiver.
What does it mean when my Siemens Handsets displays 'Connect Release No dial tone available'?
If the following appears immediately after pressing the talk key on your Siemens Handsets: Connect. Release No dial tone available; no calls can be made, it means that HiPath Cordless Enterprise is currently being used by other users. In this case, the solution is to simply repeat the call later.
What does it mean if Siemens Handsets displays 'Base 1 Outgoing and incoming calls and activation/deactivation are not possible'?
If the following appears on your Siemens Handsets: Base 1 Outgoing and incoming calls and activation/deactivation are not possible, it indicates that the mobile telephone is blocked. To resolve this, remove the battery from the mobile telephone and then re-insert it.
What does the de-crescendo tone sequence during input mean on Siemens Handsets?
If you are experiencing a de-crescendo tone sequence during input on your Siemens Handsets, it indicates that an incorrect entry was made. To resolve this, repeat the key sequence while carefully watching the display. If needed, consult the operating instructions.
How to enable ringer on my Siemens IP Phone?
If your Siemens IP Phone isn't ringing, the ringtone might be deactivated, or the 'Do Not Disturb' feature could be active. To resolve this, activate the ringer and deactivate 'Do Not Disturb'.
What to do if my Siemens IP Phone displays 'Maximum input time was exceeded'?
If your Siemens IP Phone displays 'Maximum input time was exceeded', avoid making long pauses between keystrokes when entering information.
What to do if my Siemens IP Phone displays 'The On-hook key was not pressed'?
If your Siemens IP Phone shows 'The On-hook key was not pressed', simply press the On-hook key to proceed.
What to do if my Siemens IP Phone displays 'No connection under the phone number dialled available'?
If your Siemens IP Phone displays 'No connection under the phone number dialled available', ensure you are entering the phone number correctly. If the issue persists, try calling the attendant console.
General| Architecture | Modular |
|---|---|
| Supported protocols | SIP, H.323, ISDN |
| VoIP Support | Yes |
| ISDN Support | Yes |
| Analog Support | Yes |
| Integration | CTI, CRM, ERP |
| Compatibility | Siemens |
Overview of the phone's physical layout and key components.
Information on assigning functions to sensor keys.
Procedures for answering incoming calls via handset or speaker.
Procedures for transferring calls with or without announcement.
Overview of different call forwarding types and options.
Features like call waiting and managing second calls.
Including multiple parties in a conference call.
Assigning functions to programmable sensor keys.
Setting up direct station selection keys.
Assigning external calls to specific projects using codes.
Setting and managing user passwords for menu access.
Securing the phone against unauthorized access.
Managing call reception status.
Logging into other phones using PIN.
Preparing the phone for Bluetooth device connections.
Interpreting and resolving screen error messages.
Common issues like unresponsive keys or no ringing.
To Next Page