Siemens SINAMICS V20 - Page 27

SINAMICS V20 Inverter
A5E37281078-003, 05/2016
27
Parameter
Description
Range
Factory default
Acc.
level
P1005[0...2]
-
P1014[0...2]
Fixed frequency 5 - 14 [Hz] -550.00 - 550.00 0.00 2
P1015[0...2]
Fixed frequency 15 [Hz]
-550.00 - 550.00
0.00
2
P1016[0...2]
Fixed frequency mode
1 - 2
1
2
1
Direct selection
2
Binary selection
P1031[0...2]
MOP mode
0 - 3
1
2
P1032
Inhibit reverse direction of MOP
0 - 1
1
2
0
Reverse direction is allowed
1
Reverse direction inhibited
P1040[0...2]
Setpoint of the MOP [Hz]
-550.00 - 550.00
5.00
2
P1047[0...2]
MOP ramp-up time of the RFG [s]
0.00 - 1000.00
10.00
2
P1048[0...2]
MOP ramp-down time of the RFG [s]
0.00 - 1000.0
10.00
2
r1050
CO: Actual output freq. of the MOP [Hz]
-
-
2
P1058[0...2]
JOG frequency [Hz]
0.00 - 550.00
5.00
2
P1059[0...2]
JOG frequency left [Hz]
0.00 - 550.00
5.00
2
P1060[0...2]
JOG ramp-up time [s]
0.00 - 650.00
10.00
2
P1061[0...2]
JOG ramp-down time [s]
0.00 - 650.00
10.00
2
P1080[0...2]
Minimum frequency [Hz]
0.00 - 550.00
0.00
1
P1082[0...2]
Maximum frequency [Hz]
0.00 - 550.00
50.00
1
P1120[0...2]
Ramp-up time [s]
0.00 - 650.00
10.00
1
P1121[0...2]
Ramp-down time [s]
0.00 - 650.00
10.00
1
P1130[0...2]
Ramp-up initial rounding time [s]
0.00 - 40.00
0.00
2
P1131[0...2]
Ramp-up final rounding time [s]
0.00 - 40.00
0.00
2
P1132[0...2]
Ramp-down initial rounding time [s]
0.00 - 40.00
0.00
2
P1133[0...2]
Ramp-down final rounding time [s]
0.00 - 40.00
0.00
2
P1134[0...2]
Rounding type
0 - 1
0
2
0
Continuous smoothing
1
Discontinuous smoothing
P1135[0...2]
OFF3 ramp-down time [s]
0.00 - 650.00
5.00
2
P1200
Flying start
0 - 6
0
2
0
Flying start disabled
1
Flying start always active; searches in both directions
2
Flying start active after power on, fault, OFF2; searches in both directions
3
Flying start active after fault, OFF2; searches in both directions
4
Flying start always active; searches in direction of setpoint only
5
Flying start active after power on, fault, OFF2; searches in direction of setpoint only
6
Flying start active after fault, OFF2; searches in direction of setpoint only
P1202[0...2]
Search rate: flying start [%]
10 - 200
100
3
P1203[0...2]
Search rate: flying start [%]
10 - 500
100
3
r1204
Status word: flying start V/f
-
-
4
Bit Signal 1 signal Bit Signal name 1
signal
00 Voltage reduced Yes 01 Current could not
be applied
Yes
02
Voltage reduced
Yes
03
Slope-filter started
Yes
04
Current less threshold
Yes
05
Current-minimum
Yes
07
Speed could not be found
Yes
P1210
Automatic restart
0 - 8
1
2
0
Disabled