09.91 3 Operating Sequences
3.2.3 Influencing ”AUTOMATIC” operation
DEC-SBL
YES-NO
User notes on ”RAPID OVERRIDE” :
During processing of a new NC program the feedrate override switch can be enabled with the keyswitch.
The following rapid override values can be set with the feedrate override selector switch on the customer operator
panel.
This table is only applicable when the ”Rapid override switch present” machine data is set. When this is not the case,
the setting for the ”Feedrate override switch” applies for rapid override, with a limitation of 100%!
Setting Override value in %
11
210
350
4 100
Display: Decoding Single Block YES
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
When the function is activated with ”YES”, the control generates the ”Decoding single
block active” signal.
The signal is active at the end of the block in the running part program, which is running
through with the decoding signal present.
You select, for example, the ”DECODING SINGLE BLOCK” softkey
function.
Now operate the ”Program start” key. The decoding single block is
now processed.
Operate the ”Program start” key once more. The next decoding
single block is processed ... etc.
© Siemens AG 1990 All Rights Reserved 6ZB5 410-0EQ02 3-99
SINUMERIK 810M, GA3 (BN)
To Next Page
Loading...
