Siemens SINUMERIK 810M - Selection of Operating Modes; Selection of Operating Modes with Internal Machine Control Panel

2 Operation 11.90
2.3.3 Selection of operating modes
2.3.3 Selection of operating modes
2.3.3.1 Selection of operating modes with internal machine
control panel
You call up the following named operating modes:
– PRESET (Actual Value Setting)
– MDI - AUTOMATIC (Manual Data Input / Automatic)
– JOG (Feed / Jog)
– REPOS (Repositioning)
– AUTOMATIC (Automatic operation).
The menu
shows you the
function of each
softkey.
You operate one of these softkeys.
a a a a
a
a a
a
a
a a
a
a
a a
a
a
a a
a
a
a a
a
a a a a
a a a a a a
a a a a a a
a a a a a a
a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
The basic display of the operating mode you selected is shown on the CRT.
REPOS AUTO-
MATIC
JOGMDI-
AUTOM.
PRESET
a a a a a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a
a a a a a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a
a a a
a
a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a
a a a a a
a a a a a
a a a a a
by operating this key on the machine control panel.
a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a
a a a a
a a a a
2-38 © Siemens AG 1990 All Rights Reserved 6ZB5 410-0EQ02
SINUMERIK 810M, GA3 (BN)