09.91 3 Operating Sequences
3.2.3 Influencing ”AUTOMATIC” operation
You extend the softkey menu called under ”PROGRAM CONTROL” ...
(( 810M))
(( Bild 55 von Druckerei
einmontieren
... and subsequently operate the ”DRF-HANDWHEEL-ENABLE” softkey.
Display: DRF handwheel enable YES
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
DRF
YES-NO
You have activated DRF (Differential Resolver Function). It is now possible to activate the
handweel for the selected axis.
The handwheel-to-axis assignment is defined in axial setting data (see Section 3.2.10).
It is always only possible to activate one axis with one handwheel. If a second axis is selected,
the previously selected axis is automatically deactivated (see Section 3.2.9
“HANDWHEEL”
and Section 3.2.10 “DRF” for further details).
© Siemens AG 1990 All Rights Reserved 6ZB5 410-0EQ02 3-101
SINUMERIK 810M, GA3 (BN)
To Next Page
Loading...
