What to do if Siemens SITRANS LR100 shows 'M505 No echo available'?
If the Siemens Transmitter shows the error 'M505 No echo available', it means the transmitter isn't detecting an echo, or the antenna might be dirty or defective. To fix this, clean the antenna. If that doesn't work, consider using a more suitable antenna or transmitter, removing potential false echoes, and optimizing the transmitter's position and orientation.
What to do if Siemens SITRANS LR100 Transmitter shows 'S600 Impermissible electronics temperature'?
If the Siemens Transmitter displays 'S600 Impermissible electronics temperature', it indicates that the electronics temperature is outside the specified range. You should check the ambient temperature and insulate the electronics.
What does 'S601 Overfilling' mean on Siemens SITRANS LR100 Transmitter?
If the Siemens Transmitter displays 'S601 Overfilling', it indicates a danger of vessel overfilling. To resolve this, ensure that there is no further filling and check the level in the vessel.
What causes 'M504 Error at a device interface' in Siemens SITRANS LR100 Transmitter?
If the Siemens Transmitter displays 'M504 Error at a device interface', it is caused by a hardware defect. Check connections, exchange the electronics or send the transmitter for repair.
How to troubleshoot 'F025 Error in the linearization table' on Siemens Transmitter?
If the Siemens Transmitter displays 'F025 Error in the linearization table', it's due to index markers not continuously rising, or illogical value pairs. To fix this, check the linearization table, then delete it or create a new one.
How to solve 'F261 Error in the transmitter settings' on Siemens Transmitter?
If the Siemens Transmitter shows the error 'F261 Error in the transmitter settings', it indicates an error during setup, auto false echo suppression is faulty or an error occurred when carrying out a reset. You should repeat the setup or carry out a reset.
What does 'M507 Error in the transmitter settings' mean on Siemens SITRANS LR100?
If the Siemens Transmitter displays the error 'M507 Error in the transmitter settings', it indicates an error during setup, when carrying out a reset, or auto false echo suppression is faulty. To resolve this, carry out a reset and repeat the setup.
What to do if current signal is greater than 22 mA or less than 3.6 mA on Siemens SITRANS LR100 Transmitter?
If the Siemens Transmitter current signal is greater than 22 mA or less than 3.6 mA, it suggests the transmitter electronics are defective. Depending on the device version, replace the device or send it in for repair.
How to fix 'F013 no measured value available' on Siemens SITRANS LR100?
If your Siemens Transmitter displays 'F013 no measured value available', it indicates there's no measured value during the switch-on phase or operation. You should check and correct the installation or parameter settings, and also clean the antenna system.
General| Type | Radar Level Transmitter |
|---|---|
| Frequency | 80 GHz |
| Process Pressure | Up to 3 bar |
| Output Signal | 4 to 20 mA |
| Output | 4 to 20 mA / HART |
| Communication Protocol | HART |
| Communication | HART |
| Enclosure Rating | IP68 |
| Measuring Principle | FMCW Radar |
| Measuring range | 0.08 to 30 m |
| Process Temperature | -40 to +80 °C |
| Power Supply | 12 to 30 V DC |
| Housing Material | Aluminum |
Highlights specific safety precautions for explosive environments.
Specifies requirements for individuals operating the device.
Defines the intended application and conditions for the transmitter.
Alerts users to hazards from misuse.
Lists essential safety guidelines for operation.
Provides guidelines for ambient and process conditions.
Gives specific steps and considerations for installation.
Explains how to configure the device for flow measurement.
Details safety and requirements before electrical connection.
Shows wire assignments for the connection cable.
Explains how to identify and fix malfunctions.
Details how to interpret error codes and messages.
Describes device status indicators.
Presents detailed specifications of the device.
To Next Page