Siemens ULTRAMAT 23 - Page 6

I-2
Operating Instructions ULTRAMAT 23 Gas Analyzer
C79000-B5276-C216-03
5 Operation 5-1.......................................................
5.1 General 5-3.....................................................
5.2 Display and Input Panel 5-4.......................................
5.3 Warm-up Mode 5-7..............................................
5.4 Measuring Mode 5-8.............................................
5.5 Input Mode 5-8..................................................
5.5.1 Code Levels 5-9.................................................
5.5.2 Key Operations Step-by-step 5-10...................................
5.5.3 Using the ESC key 5-12...........................................
5.6 Recoding the Analyzer 5-13........................................
5.7 Analyzer Status 5-15..............................................
5.7.1 Analyzer Status: Status 5-15.......................................
5.7.1.1 Analyzer Status: Status: Logbook/Faults 5-15.........................
5.7.1.2 Analyzer Status: Status: Maintenance Request 5-16...................
5.7.1.3 Analyzer Status: Status: AUTOCAL Deviation 5-16....................
5.7.1.4 Analyzer Status: Status: O2 Sensor Status 5-16......................
5.7.2 Analyzer Status: Diagnostic Values 5-17.............................
5.7.2.1 Analyzer Status: Diagnostic Values: IR Diagnostic Values 5-17..........
5.7.2.2 Analyzer Status: Diagnostic Values: O2 Diagnostic Values 5-18.........
5.7.2.3 Analyzer Status: Diagnostic Values: Pressure Sensor Diagnosis 5-18....
5.7.2.4 Analyzer Status: Diagnostic Values: Other Diagnostic Values 5-18.......
5.7.3 Analyzer Status: Factory Settings Hardware 5-19.....................
5.7.4 Analyzer Status: Factory Settings Software 5-19......................
5.8 Calibration 5-21...................................................
5.8.1 Calibration: Calibrate IR Channels 5-21..............................
5.8.1.1 Calibration: Calibrate IR Channels: Set Span Gas Values 5-21..........
5.8.1.2 Calibration: Calibrate IR Channels: Start with Range MR 1/2 5-22.......
5.8.2 Calibration: Calibrate O2 Sensor 5-22................................
5.8.2.1 Calibration: Calibrate O2 Sensor: O2 Cal. after Install 5-22.............
5.8.2.2 Calibration: Calibrate O2 Sensor: O2 Zero Cal. 5-23...................
5.8.3 Calibration: Calibrate Pressure Sensor 5-23..........................
5.8.4 Calibration: AUTOCAL 5-24........................................
5.9 Parameters 5-26..................................................
5.9.1 Parameters: Measuring Ranges 5-26................................
5.9.1.1 Parameters: Measuring Ranges: Switch Ranges 5-26..................
5.9.1.2 Parameters: Measuring Ranges: Change Ranges 5-27.................
5.9.1.3 Parameters: Measuring Ranges: Hysteresis 5-27.....................
5.9.2 Parameters: Limit values 5-28......................................
5.9.3 Parameters: Time Constants 5-29...................................
5.9.4 Parameters: Pump/LCD Contrast 5-29...............................
5.9.4.1 Parameters: Pump/LCD Contrast: Adjust Pump 5-30..................
5.9.4.2 Parameters: Pump/LCD Contrast: Adjust LCD Contrast 5-30............
5.10 Configuration 5-33................................................
5.10.1 Configuration: Inputs/Outputs/Pump 5-33............................
5.10.1.1 Configuration: Inputs/Outputs/Pump: Analog Outputs 5-33..............
5.10.1.2 Configuration: Inputs/Outputs/Pump: Assign Relays 5-35...............
5.10.1.3 Configuration: Inputs/Outputs/Pump: Binary/Sync Inputs 5-38...........