Simplex 4100U-S1 - Displaying Event Time; Procedure

86 pages

To Next Page

To Previous Page

2-7

1. Select the point by repeatedly pressing the <ALARM ACK> key (for a point in alarm),

<FAULT ACK> (for a point in fault), or <ISOLATE ACK> (for an isolated point) until

the desired point is displayed.

2. Press the <EVENT TIME> key. The time and date that the point entered that state will be

displayed.

Displaying Event time

Procedure

Main Page

Default Chapter4
- Approvals4
- Copyright and Trademark Information4
- Document4
- Firmware Revision4
- Manufacturer4
- Table of Contents6
Chapter 1 Overview11
- Introduction11
- In this Chapter11
Typical Panel Layout12
- Overview12
Basic System Description13
- Overview13
Control Keys & Indicators16
- Overview16
Normal Appearance of Operator Interface17
- Description17
Chapter 2 Managing Alarm Conditions19
- Introduction19
- In this Chapter19
Acknowledging Alarms20
- What the System Does When an Alarm Occurs20
- Overview - Acknowledging Alarms20
- Procedure21
Isolating (Silencing) the EWS or External Bell22
- Overview22
- Isolating the EWS22
- Isolating the External Bell22
- Isolating the Zone22
Isolating ACF Outputs23
- Overview23
- Operation23
- Restoration23
Resetting Air Conditioning Control24
- Overview24
- Indication24
- Resetting24
Displaying Event Time25
- Procedure25
Resetting Points26
- Overview26
- Reset Procedure26
Chapter 3 Managing Fault and Isolate Conditions27
- Introduction27
- In this Chapter27
Acknowledging Fault or Isolate Conditions28
- What Acknowledge Does28
- Panel Operating Procedure - Fault Condition29
- Resetting Fault Conditions29
Viewing Fault or Isolate Conditions30
- Overview30
Chapter 4 Testing and Controlling Points31
- Introduction31
- In this Chapter31
Alarm and Fault Test for Zones32
- Alarm Test32
- Fault Test32
Isolating and De-Isolating Zones33
- Isolating a Zone33
Disabling and Enabling Points34
- Overview34
- Disabling a Point34
- Enabling a Point34
Turning a Point on or off35
- Overview35
- Turning a Point off35
- Turning a Point on35
- Returning a Point to Automatic Operation35
- Sounder (Buzzer)35
Chapter 5 Selecting Points for Status or Control37
- Introduction37
- In this Chapter37
Selecting Points from the Menu38
- Overview38
- Procedure38
Selecting Points with the Entry Keypad39
- Overview39
- Selecting Points40
Chapter 6 Displaying and Modifying Detailed Point Attributes41
- Introduction41
- In this Chapter41
Display-Only Attributes42
- Select a Point42
- See the Attributes42
- Summary of Display-Only Attributes43
Modifiable Point Attributes44
- Overview44
- Select a Point44
- See the Attributes44
- Summary of Modifiable Attributes44
Chapter 7 Setting Access Levels and Logging in47
- Introduction47
- In this Chapter47
Operator Access Levels48
- Overview48
Logging in and out of the System49
- Introduction49
- Log in Procedure49
- Log out Procedure50
Chapter 8 Viewing and Clearing Historical Logs53
- Introduction53
- In this Chapter53
Viewing and Clearing the Historical Alarm and Fault Logs54
- Viewing Logs54
- Clearing the Logs54
Chapter 9 Service-Related Operations55
- Introduction55
- In this Chapter55
Setting Time and Date56
- Procedure56
Displaying Software Revision57
- Overview57
Viewing Card Status Information58
- Overview58
- Procedure58
Displaying Network Node Information59
- Procedure59
Lamp Test60
- Procedure60
Displaying Idnet & Mapnet Device Status61
- Introduction61
- Truealarm Sensor Display Values62
Chapter 10 System Test Procedures65
- Introduction65
- In this Chapter65
Walk Test66
- Overview66
- Walktest™ by Group66
- Zone Coding Option66
- Silent Walk Test67
- Enabling Walk Test67
- Walk Test Operation68
Walk Test™ FEATURES69
- Introduction69
- Abort Audible and Delay on Reactivation69
- Active/Not Active69
- Auto Abort on Alarm69
- Auto Abort on Time-Out69
- Control List69
- Delay before Reset70
- Logging Option (Log/No Log)70
- Monitor Zone List70
- Programmer Configuration70
- Sig/No Sig (Silent Walk Test™ Selection)70
- Fault Audible71
Walk Test™ PROCEDURES72
- How to Enter Walk Test Mode73
- How to Exit Walk Test Mode73
- How to Turn a Point off74
- How to Turn a Point on75
- How to Return a Point to Auto75
- How to Enable a Disabled Point76
- What to Do in Case of System Malfunction77
Chapter 11 Printing Reports79
- Introduction79
- In this Chapter79
Setting Printer Options80
- Available Options80
Printing a Report81
- Overview81
- Procedure81
Chapter 12 Maintenance Procedures83
- Introduction83
- In this Chapter83
Weekly Tests84
- Procedure84
- Battery Test84
Monthly Tests85
- Procedure85
Annual Tests86
- Procedure86

Simplex 4100U-S1 - Displaying Event Time; Procedure

Table of Contents

Related product manuals