Simplex 6400 - Connecting 6400 to Externally-Powered Coded Relays (Optional); Connecting 6400 to Coded Relays Using 6400 Line Voltage (Optional)

46 pages

To Next Page

To Previous Page

FROM EXTERNAL

POWER/INTERFACE BOARD

ASSY NO. 562-765

Figure 28

CONNECTING 6400 TO EXTERNALLY-POWERED CODED RELAYS (OPTIONAL)

CODED SIGNAL

NEUTRAL

POWER/INTERFACE BOARD

ASSY NO. 562-765

Figure 29

CONNECTING 6400 TO CODED RELAYS USING 6400 LINE VOLTAGE (OPTIONAL)

firealarmresources.com

Main Page

Table of Contents3
Pre-Power Adjustments6
General Notes6
Setting DIP Switches on CPU Board7
Cpu Board7
Bcd Output Format Settings7
Generator Settings8
Keypad Lockout & Timekeeping Settings8
Synchronous Settings8
Board (Optional)9
6400 Coded/Impulse Board9
6400 Coded Board9
Remote Coded Relay Settings (6400 Only)10
Secondary Clock Settings10
Rapid Rate Advance Settings11
Impulse Accumulator Settings11
Setting DIP Switches on WWV Interface Board12
Wwv Interface Board12
Wwv Communication Settings12
Wwv Baud Rate Settings12
Section 2 - Installation Wiring13
General Notes13
Connections to Power/Interface Board13
Power/Interface Board13
Ac Power Wiring 115Vac14
Ac Power Wiring 230Vac14
Typical Wiring for Six Circuits of Bells/Horns Using External Power (6400 Only)15
Typical Wiring for Six Circuits of Bells/Horns Using 6400 Line Voltage15
Wiring for External Input16
Connecting Tcc to Celestra Secondary Clocks16
Secondary Clocks17
Connecting Tcc to Synchronous Secondary Clocks Using Tcc Line Voltage17
Connecting Tcc to Externally-Powered Transmitter18
Generator18
Connecting Tcc to Transmitter/Generator Using Tcc Line Voltage18
Connecting 6400 to Externally-Powered Coded Relays (Optional)19
Connecting 6400 to Coded Relays Using 6400 Line Voltage (Optional)19
Connections to Impulse Interface Board (Optional)20
Impulse Interface Board20
Impulse Power Supply Wiring 115Vac (Optional)21
Impulse Power Supply Wiring 230Vac (Optional)22
13, 14, & 15 (Optional)23
Connecting Tcc to 3-Wire Impulse Secondary Clocks (B Disconnect)24
CONNECTING TCC to 3-WIRE SYNCHRONOUS SECONDARY CLOCKS - 6, 7, A, 8 9 (OPTIONAL)25
Types 1 , 2, 3, 13, 14, & 15 (Optional)26
Connecting Tcc to 2 or 3-Wire Dual Motor Secondary Clocks -Type 10 (Optional)26
Types 11 & 12 (Optional)27
Type 16 (Optional)28
Secondary28
Clocks - Type 17 (Optional)29
Connections to 6800 Coordinated Universal Time Receiver (Optional)30
Connection to Extended Battery (Optional)31
Final Checkout31
Operating Manual Override Switch(Es) for ON/OFF and PULSE Type Events (6400 Only)32
Operating Manual Override Switch(Es) for DELAY Events (6400 Only)32
Operating Manual Override Switch(Es) for SYNCHRONOUS Output32
Signals32
Operating Manual Override Switch(Es) for GENERATOR Output33
Operating Manual Override Switch(Es) for SERIAL BCD Output33
Section 4 - Operating Manual Override Switches (Optional Equipment)34
Operating Manual Override Switch (CIRCUIT ONE) for REMOTE RELAYS34
Operating Manual Override Switch for SECONDARY CLOCK Output34
Advance Rates (Impulse Secondary Clocks)34
Appendix A - General Mounting Instructions36
Mounting Tcc Door, Retainer Panel, & Mounting Plate to Back Box36
Connecting Cpu to Power/Interface37
Board37
General Notes38
Mounting Instructions - Slides & Cable Carrier38
Installing Rack-Mount Slides (6400 Only)39
Installing Rack-Mount Cable Carrier (6400 Only)39
Appendix C - Wwv Interface Board - Installation Instructions40
INSTALLING Wwv40
Interface Board40
Appendixd - 6351 Keypad Operation and Basic Keypad Entries41
Introduction41
Keypad Operation41
General Notes41
Lcd Display41
Keypad Normally Active Vs. Keypad Normally Inactive42
Keypad Modes42
Keypad42
Basic Entries43
To Enter Hour Format (12 or 24) for LCD43
To Set the Time and Day of the Week43
To Set the Date43
Lcd after Depressing Time Key43
Lcd after Depressing43
Date Key43
To Program the Automatic Daylight Saving Time (DST) Changes44

Simplex 6400 - Connecting 6400 to Externally-Powered Coded Relays (Optional); Connecting 6400 to Coded Relays Using 6400 Line Voltage (Optional)

Table of Contents

Related product manuals