IMPORTANT SAFETY INSTRUCTIONS
When using this machine, basic safety precautions should always be followed including
the following:
Read ail instructions before using this machine.
DANGER -
To reduce the risk of electric shock:
• The machine should never be left unattended when plugged in. Always unplug the
machine from the electric outlet immediately after using and before cleaning.
• Always unplug before relamping. Replace bulb with the same type rated 15 watts.
Besureta replace the face plate which coversthe light bulb before operating the machine.
WARNING -
Ta reduce the risk of burns, fire, electric shock
or injury to persons:
• Be sure that the electrical voltage of the socket outlet (wall receptacle) is the same as
the rated voltage of the motor.
• Use this machine only for its intended use as described in this Operator's Guide.
Use only attachments recommended by the manufacturer as contained in the
Operator's Guide.
• To disconnect, turn ail controls to the off ("0") position, then remove plug from outlet.
• Disconnect the power-line plug from the socket outlet or switch the machine off when
making any adjustments in the needle area, such as threading needle, changing needle,
changing needle plate or changing presser foot, etc.
• Always unplug the machine from the electrical outlet when removing covers, lubricating,
or when making any other user servicing adjustments mentioned in the Operator's Guide.
• Do not attempt to adjust the motor belt. Contact your nearest Service Center should any
adjustment be required.
• Do not unplug by pulling on cord. Ta unplug, grasp the plug, not the cord.
• Handle the foot controller with care and avoid dropping it on the floor. Be sure not to
place anything on top of it.
• Always use the proper needle plate. The wrong plate can cause the needle to break.
• Do not use bent needles.
• When sewing, keep fingers away from ail moving parts. Special care is required around
the sewing machine needle.
• Do not pull or push fabric while stitching. It may deflect the needle causing it to break.
• Before removing the bobbin case, remove plug from the socket outlet.
• For double insulated machines, when servicing use only identical replacement parts.
• Never operate the machine if it has a damaged cord or plug, if it is not working properly,
if it has been dropped or damaged, or dropped into the water. Return the machine to
the nearest authorized dealer or Service Center for examination, repair, electrical, or
mechanical adjustment.
• Never operate the machine with any air openings blocked. Keep ventilation openings
of the machine and foot controller free from the accumulation of lint, dust, and loose cloth.
• Never drop or insert any object into any opening.
• Do not use outdoors.
2
• Do not operate where aerosol (spray) products are being used or where oxvgen is being
administered.
• Do not allow to be used as a toy. Close attention is necessary when the machine is used
by or near children.
SAVE THESE INSTRUCTIONS
Servicing should be performed by an authorized service representative.
This product is intended for household use.
INSTRUCCIONES IMPORTANTES
AI utilizar esta maquina, se deberan seguir siempre las precauciones basicas de
seguridad, incluida la siguiente:
PELIGRO -
Para reducir el riesgo de descarga eléctrica:
• La
maquina nunca debe permanecer descuidada después de enchufada. Debe siempre
ser desenchufada inmediatamente después de usarla y antes de limpiarla.
• Desenchufar siempre antes de efectuar el cambio de la lampara. Reemplazar la bombilla
por el mismo tipo de 15 watts. Asegurarse de reponer la placa frontal que cubre la
bombilla, antes de accionar la maquina.
ADVERTENCIA -
Para reducir el riesgo de corto circuitos, incendio,
descarga eléctrica
0
dai'los persona les:
• Asegurarse que el voltaje dei enchufe sea el mismo dei voltaje dei motor.
• Usaresta maquina solamente para los propositos indicados en este manual de manejo.
Usar solamente accesorios recomendados por el fabricante coma indicado en el
manual de manejo.
• Para desconectar, girar los controles para la posicion off ("0") y desenchufar.
• Desenchufar 0 desconectar la maquina para efectuar cualquier ajuste en el area de
la aguja, la plancha corredera 0 el prensatelas.
• Desenchufar siempre la mâquina al quitar las cubiertas, al lubricar 0 al efectuar
cualquier otro ajuste mencionado el el manual de manejo.
• No debe tratar de ajustar la correa dei motor. Siprecisa algun ajuste,pongase en contacto
con el servicio técnico mas proximo.
• No desenchufar tirando dei cordon. Para desenchufar, agarre el enchufe no el cordon.
• Manipular el pedal controlador con cuidado y evitar dejarlo caer. Asegurarse de no
colocar nada sobre el mismo.
• Usar siempre la plancha corredera correcta.
La
placa incorrecta puede causar la
rotura de la aguja.
3
To Next Page
Loading...
