Siruba PK511 User Manual

SiMUaA ® Sew Reach
lntrnrl11r.tion
IMPORTANT SAFETY INSTRUCTIONS
Putting -Ing ayatems Into operation Is prohib ited until It has been ascertained that the sewing syatems In which these
-Ing machlnea wtll be bullt Into , ha ve conformed with the aa fety regula tions in your country .
Techntcel ~Ice fOf thoae aewlng syatem• Is also prohibited.
1. Observe the baalc aafety ,,,_aurea , Including , but n ot limited to th e followlng onea, whenever you uae the machine.
2.
Read all the lnatructlons , Including, but not llmlted to th is lnatructlon Manual before you use the machine.
In addition, k"P this Instruction Manual so that you may read It at anytime when nec ,esaary.
3. Uae the machine alter It has been ascertained that It confo r ms with safety rules/standards valld In your country.
4.
All aafety devlCN m ust be In position when the machine la ready for work or In oper atio n.
The operation without the apeclfled safety devices ls not allowed.
5.
Thi s mechlne shall be operated by app ropriately-trained operators .
6. FOf your personal protection, - recommend that you wear safety glas ses.
7. FOf the following , tum off the power switch or dlaconnect the power plug of the machine from the receptacle.
7-t For threedlng needte(a), looper , spreader etc . and replacing bobbin .
7-2 For
replacing part(s) of needle, prea9« loot , throat plate, looper , spreader. feed dog , needle guard, folder, cloth gu i de etc.
7-3
For repair work .
7-4 When leav i ng the working place or when the wortdng place is unattended.
7-5 When using clutch motors without applying brake, It has to be waited until the motor stopped to tally.
8.
H you should al low oll, gr- , etc. used with th e machi ne and devices to come In contact with your eyes or skin or
swallow any of such l lquld by mistake, Immediat ely wash the co n tacted areea and cons u lt a medical doctor .
9. Tampering with the llve pans and devices, ,-gardless of whether the machine Is powered, la prohibited .
10 . Repair, remodeling and adjust me nt works must only be done by ap propr iate ly trained techn ic ian s or speci ally s kllled
personnel. Only spare parts designated by can be used for repairs.
11 . General ma intenance and I nspection work s have to be done by approp riat ely tra i ned personnel.
12. Repair and maintenance work s of electrlcel components shall be con du cted by qualtt l ed electric technicians or under
the audit and guidance of apeclally skllled personne l.
Whenever you ttnd a !allure of any of electrlcal components , Immedia tely stop the machine.
13 . Before maki ng repair a nd maintenance works on the machine equipped with pne umatic parts such as an air cy linder ,
the air compreuor hu to be detached from the machine and the compreHed air supply has to be cut off . Exlatlng
residua! air pressure alter dis co nnecting the air comp re ssor from the machine has to be expelled. Exception• to this
are only adjustmen ts and performance checks done by appropriately trained technician • or apeclally akllled person nel.
14 . Pertocltcelly clean the machine throughout the period of use .
15. Grounding the machi ne Is always necessary for the normal operation of the machine . The machine has to be operated
In an environment that Is free from st rong noise sou r ces suc h as high-frequency welder .
16. An appropriate power plug h as to be attached to the mach ine by elec trtc technic ians. Power plug has to be connected
to a grounded receptacle.
17 . The machine la only allowed to be used for the purpose Intended. Other used are not allowed.
18.
Remodel or modify the machine in accordance with the safety rules/standard s while taking all the effect i ve safety
-urea .
naurnes no rNponslblllty for damage caused by remodeling or modificat io n of the machine.
19. Warning hint• are marked with the two shown symbol •.
A Danger of Injury to operator or service staff
& Items requiring special atten tion
.....
.....
.....
....
....
~ ~
1
~~
~II
~
2
( -¥ I h~~ 1, 1:\')
e • There I• the pc>Mlblllty that slight to aertous Injury or dNth may be caused.
• There I• the poulblllty that Injury may be caused by touching moving part.
e • To perform -Ing work with aafety guard .
• To perform -Ing work with aafety cover .
• To perform aewlng work with safety protection device .
e • Tum OFF the power and perform " threading '", •• repl aceme nt of bobbin or
,-die ", " clNn l ng ", " adjustment" and "lubrtcatlon"'.
P01
From the library of Superior Sewing Machine & Supply LLC • www.supsew.com

Siruba PK511 Specifications

General

Brand	Siruba
Model	PK511
Category	Sewing Machine
Language	English