SPECIFICATIONS
SPECIFICATIONS
Technical Data
The content of the TECHNICAL DATA pages should be used as necessary to fine-tune and perform
additional adjustments required on the snowmobile. Vehicles used at high altitudes, above 600 m
(2000 ft) should be fitted with a high altitude kit. Further inquiries should be directed to your distributor
service representative.
MODEL SKANDIC LT
SKANDIC
WT/SWT/SUV
SKANDIC SUV
E
EE
EN
NN
NG
GG
GI
II
IN
NN
NE
EE
E
Type 443 552 593
Maximum HP RPM [1] ± 100 RPM
6900 6950 7000
Reed Valve P/N N/A 420 924 519 420 924 519
C
CC
CA
AA
AR
RR
RB
BB
BU
UU
UR
RR
RE
EE
ET
TT
TI
II
IO
OO
ON
NN
N
Carburetor type VM 32 2xVM34 2xVM38
Main jet
180 190 330
Needle jet O-0 (159) P-0 (159) P-9 (480)
Pilot jet
50 40 40
Needle identification — clip position 6DGY12-3 6DH4-2 6DFHL24-3
Slide cut-away
3 2.5 2.5
Float adjustment ± 1 mm (± .04 in) 35.5 (1.392) 23.9 (.94) 18.1 (.710)
Air screw adjustment ± 1/16 turn
1.5 0.5 2.0
Idle speed ± 200 RPM 1650 1650 1900
Type Regular unleaded gasoline
Fuel
Octane
87 (Ron + Mon)/2 inside North America
91 Ron outside of North America
Gas/oil ratio Oil injection
E
EE
EL
LL
LE
EE
EC
CC
CT
TT
TR
RR
RI
II
IC
CC
CA
AA
AL
LL
L
Ignition timing BTDC [3] mm (in) 2.79 (.110) 2.77 (.109) 3.0 (.118)
Trigger coil gap mm (in)
0.45 - 0.55
(.018 -.022)
0.40 - 0.60
(.016 -.024)
N.A.
T
TT
TR
RR
RA
AA
AN
NN
NS
SS
SM
MM
MI
II
IS
SS
SS
SS
SI
II
IO
OO
ON
NN
N
Gear ratio
1: 2.59
1
st
gear 1: 2.93
2
nd
gear 1: 2.04
Rgear1: 3.57
1
st
gear 1: 2.82
2
nd
gear 1: 1.7
Rgear1: 3.44
Engagement speed ± 100 RPM
3200 2500 2500
Drive pulley calibration screw position
— —
3
Pulley
distance
Z
mm
(in)
39 ± 0.75
(1.535 ± .030)
41.8 ± 0.75
(1.647 ± .030)
35.5 ± 0.75
(1.398 ± .030)
X ± 0.75 mm (± .030 in) 37.0 (1.457) 35.0 (1.380) 37.0 (1.457)
Offset
Y Dimension Y must exceed X by 0.75 mm (.03 in) to 2.25 mm (.09 in)
Driven pulley preload ± 0.7 kg (± 1.5 lbf) Not applicable 7.5 (16.5) 7.5 (16.5)
Deflection ± 5 mm (± 13/64 in) 32 (1-1/4) 32 (1-1/4 40 to 50 (1.6 to 2.0)
Drive belt
adjustment
Force [4] kg (lbf) 11.3 (25)
Deflection mm (in) 40 – 50 (1-9/16 – 1-3132)
Track
adjustment
Force [5] kg (lbf) 7.3 (16)
22 / 24 2006-1 Predelivery
To Next Page
Loading...
