SLE SLE4000 - Trouble Shooting

312 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

(Model K) Page 141

Trouble shooting

Table of Contents

Default Chapter3
- Table of Contents3
- Warnings and Cautions7
1 Warnings and Cautions8
- Warnings8
- Cautions9
2 Principles of Operation12
- Electronic System12
- Pneumatic System13
- Description of Symbols15
3 Description of Symbols16
4 Equipment List20
5 Engmode22
- Accessing the Calibration Programs22
- Ventilator Calibration Program24
- O 2 & Flow System Calibration25
- Reset Elapsed Time26
- Language Selection26
- Activation of Language Selection Program Form User Interface27
- Exit27
- Touch Screen Calibration Program28
6 Component Replacement Procedure30
7 Preparing the SLE400031
8 Component Replacement (Electronic Unit)33
- N6631/21/CF/50 Compact Flash Card33
- N6631/LX800 PC Board33
- N6634/OEM2 CAN Card34
- N6631/2216 Serial Controller (Touch Screen)34
- L0275/OEM2 Computer/Display Control Assembly35
- A0763/4B Control/Monitor Board36
- M0915 Power Supply Unit37
- M0901 Batteries38
- A0761 Transducer PCB Assembly39
- N6631/13 Inverter PCB40
- N6631/02 LCD & N6631/05 Touch Screen41
9 Component Replacement (Pneumatic Unit)43
- Duckbill and Conical Filters43
10 A0763/4B Monitor and Control Board52
- A0763/4B Board Progammable Devices52
- A0763/4B Board Hardware Identifier53
11 Electrical Safety Testing of the SLE400057
12 PSU Testing61
13 Ventilator Power up and Power down64
14 Back-Up Battery Charging65
- Battery Indicator65
15 Extended Storage67
16 Maintenance and Overhaul70
- Preventative Maintenance Kit70
- 36 Month Preventative Maintenance Procedure72
- Month and 48 Month Overhaul Procedures80
- Month / 10,000 Hour Overhaul Procedure82
- Month / 20,000 Hour Overhaul Procedure90
- Month Overhaul Procedure Using N9410/48/G Overhaul Kit92
17 Calibration Procedure for V4.3.1 & V4.3.2 Software96
- Equipment Required for Calibration96
- Preliminary Inspection before Calibration96
- Pneumatic Set up97
- Calibration of Controller and Monitor Subsystems100
- Controller "Block and Leak" Pressure Sensor Calibration102
- Controller Blender Pressure Sensor Zeroing and Input Pressure Reg. Trim103
- Mean Jet Pressure Regulator Calibration104
- Forward Jet Pressure Regulator Calibration106
- Wave Shaping for Leading and Trailing Edge of Insp. Phase107
- O 2 System Calibration108
- Flow System Calibration108
- Pressure Triggering Verification108
- Gas Fail Detection Verification109
- Blender and Oxygen Monitoring Verification110
- Soak Test111
- Battery Charge Verification111
- Total Power Fail Alarm Test111
- Pressure Calibration Verification112
18 Functional Testing114
- Ventilator Setup114
- Trouble Shooting141
19 Trouble Shooting Chart142
20 Software Version History152
- Technical Information153
21 Oxygen Calibration Routines154
- One Point or 100% Oxygen System Calibration154
- Two Point or 21% & 100% Oxygen System Calibration154
22 Alarms156
- Alarm Protocols156
- Alarm Sounds156
- Alarm Descriptions and Actions to be Taken157
- Software and System Fail Protocols176
23 Cleaning, Disinfection and Sterilization177
- Preparation of a New Ventilator177
- Cleaning and Disinfection of an In-Service Ventilator177
- Cleaning Method178
- Disinfection Method179
- Sterilization Method180
24 Technical Specification181
- Operating Modes Conventional Ventilation181
- Exhalation Block Port Jet Sizes182
- Measurement186
- Alarms187
- Patient Circuits188
- Outputs189
- Gas Supplies190
- Power, Dimensions, Classification Etc191
- Classification191
- Environmental Storage Conditions191
25 EMC Compliance192
- Electromagnetic Immunity193
- Recommended Separation Distances between Portable and Mobile RF Communications Equipment and the SLE4000195
26 Ventilator Labelling196
- Sle4000196
27 Electrical Block Diagram198
28 L0288/KV Pneumatic Unit Layout & Schematic199
- Layout199
- Schematic200
29 Main Loom Circuit Diagram201
30 L0275/OEM2 Assembly Schematic202
31 A0761 Circuit Diagram204
- Transducer PCB Assembly204
32 A0763/4B Circuit Diagrams206
- Micro Controller206
- Conventional Valve Drive207
- Power Distribution and Hardware Identifier208
- Analogue Valve Drive / Non Volatile Memory / Interboard Comms209
- High Speed Valve Drive210
- Analogue Data Acquisition/Monitor Port211
- Control & Monitor, PCB PSU Circuit212
- Control & Monitor, Micro Non-Isolated213
- Control & Monitor, Micro Isolated214
- Control & Monitor, Analog Isolated215
- Control & Monitor, Alarm Controller216
33 Illustrated Parts List218
- Ventilator Assembly220
- Base Plate and Side Door Assembly227
- Front Facia Assembly229
- Electronic Module231
- Pneumatic Module252
- DISS Air and Oxygen Fittings264
34 Equipotential Stud Modification268
- Equipotential Stud Connection269
Appendix 1. Calibration Checklist273
Appendix 2. Check List281
Appendix 3. TB & si Index286
35 Technical Bulletin & Service Information Letters286
- Service Information Letters286
- Technical Bulletins288
Appendix 4290
- Overview291
- Data and Pinout Description291
- Cable291
- Parameter Descriptions and Format292
- List of Parameters292
- Table of Current Alarm Condition Codes295
- RS232 Connection Settings and Testing Data Output297
- Glossary297
36 Rs232290
- Warnings for RS232290
- Location of RS232 Port290
Appendix 5. Vuelink300
37 Vuelink Technical Data300
- Glossary300
- Connecting the SLE4000 to the Vuelink Patient Monitor300
- Parameter Descriptions301
- Data Transferred to the Vuelink System from the SLE4000302
- Alarm and Inoperative Indications304
- Vuelink Task Window Layout307
- Notes on General System Behaviour308
- Activation of Vuelink309
- Disabling Vuelink310

Related product manuals

Preview: SLE SLE5000