Smeg CWG420D - User Manual

Questions and Answers

T
Theresa BrownAug 12, 2025
Why does my Smeg CWG420D Dishwasher have poor washing results?
- P
  pdunnAug 12, 2025
  Poor washing results with your Smeg Dishwasher can stem from several issues. Start by checking if the spray arm washing holes and nozzles are blocked by dirt or limescale, and clean them if necessary. Ensure the filter isn't fouled. Verify you're using the correct type and amount of detergent and rinse aid. Also, make sure plates and glasses are arranged correctly. If the water temperature is low, contact After-Sales Service. Select a longer washing cycle for very dirty dishes. If detergent or rinse aid isn't being supplied, a worn or broken pipe inside the peristaltic pump may need replacement by the After-Sales Service.
J
Jennifer ThomasAug 16, 2025
What to do if Smeg CWG420D dishes not properly dried?
- O
  Olivia VelezAug 16, 2025
  If your Smeg Dishwasher is not drying dishes properly, the rinse aid might be unsuitable or not delivered correctly. Also, high water hardness or large amounts of dissolved salts can be the cause. Check the rinse aid container to ensure it's appropriate for your water type. If the issue continues, it's best to contact the After-Sales Service.
S
sjohnsonAug 20, 2025
Why the washing program does not start in Smeg Dishwasher?
- D
  David SmithAug 20, 2025
  If the washing program on your Smeg Dishwasher won't start, it could be because the dishwasher is still filling—wait until the word 'FILL' disappears from the display. If the word 'CLOSE' remains on the display even after closing the door, you should contact the after-sales service.
B
Brandy AtkinsAug 23, 2025
How to fix stains on glasses and cutlery from Smeg CWG420D Dishwasher?
- M
  Michelle LynchAug 25, 2025
  If you see stains on glasses and cutlery after using your Smeg Dishwasher, the drain hose might be incorrectly positioned or partially blocked. Check that the dishwasher drain hose and drain are unobstructed and not positioned too high. Refer to the connection diagram for proper setup.
S
Scott GilmoreAug 27, 2025
What to do if there is water in tank after pump-out in Smeg CWG420D Dishwasher?
- J
  James DrakeAug 28, 2025
  If there's water in the tank of your Smeg Dishwasher after it pumps out, the drain hose might be incorrectly positioned or partially obstructed. Ensure the dishwasher hose and drain are unobstructed and not too high up. Consult the connection diagram for guidance.
V
vstephensAug 31, 2025
Why Smeg Dishwasher has inadequate rinsing?
- P
  Patricia BerryAug 31, 2025
  If your Smeg Dishwasher isn't rinsing adequately, it could be due to unsuitable rinse aid or incorrect delivery, or the rinsing temperature might be too low. Check the rinse aid container to ensure it's appropriate for your type of mains water. Also, check the boiler temperature setting. Restore T Stop ON and/or connect the appliance to a hot water supply. If problems persist, contact the after-sales service.
K
Karen ScottSep 3, 2025
How to troubleshoot if light S1 does not come on in Smeg CWG420D Dishwasher?
- C
  christophermorenoSep 4, 2025
  If light S1 on your Smeg Dishwasher isn't coming on, the cause may be a mains power failure. Check the electrical mains connection.
T
Taylor AndersonSep 8, 2025
What does error Err05 mean on a Smeg CWG420D?
- S
  Sean McleanSep 8, 2025
  If your Smeg Dishwasher displays Err05, it indicates a tank water filling malfunction. Ensure the water intake tap is turned on and that there's adequate dynamic pressure in the intake system. Inspect the water intake filter and clean it if necessary. If the problem continues, contact the After-Sales Service.