Sony STR-DN1050 - Page 19

19
STR-DN1050
FIX MODEL AND DESTINATION MODE
This mode is to fi x the set for model & destination.
When turning on the set, the message below appears if the setting
is not fi xed with its model or destination.
Items Display
AREA/DESTINATION
NOT FIX
D E S T. U N F I X
Procedure:
1. Press the [
?
/
1
] button to turn on the main power.
2. While pressing [DISPLAY] button, press and release the
[A.F.D./2CH], [MOVIE], [MUSIC] button in order, the
message “SPECIALIZE” appears.
3. Press the [
M
] or [
m
] key of the remote commander, the
message “<SPECIAL>” appears.
4. Press the [
] key of the remote commander to enter the
Special Menu List.
5. Each time the [
M
] or [
m
] key of the remote commander is
pressed, the item is switched in order as follows.
Items Display
SYSTEM VERSION S Y S v X. X X X
MAIN VERSION M A I N v X. X X
VIDEO VERSION V I D E O v X. X X
OSD VERSION O S D v X. X X
DSP SFLASH1 VER S F L A S H v X. X X
NETWORK VERSION N E T v X. X X
MODEL display M O D E L
DESTINATION setting D E S T I N Y
MODEL &
DESTINATION check
M O D E L & A R E A
6. Go to MODEL display and press the [ ] key of remote
commander.
7. The message as below appears.
Items Display
Model N105 fi x N 1 0 5 f i x
8. Either one of the display below appears according to the
destination of the set.
Items Display
Destination D E S T U N F I X
Destination UCA fi x U C A f i x
Destination J fi x J f i x
Destination
TW/SAF fi x T W f i x
Destination SP/CN fi x C N f i x
Destination KR fi x K R f i x
Destination E2/E3 fi x C H 3 f i x
Destination CEL fi x C E L f i x
Destination AU fi x A U f i x
Destination SP fi x S P f i x
Destination E51 fi x E 5 1 f i x
Destination BR fi x B R f i x
Destination AR fi x A R f i x
Destination MX fi x M X f i x
9. Press the [
M
] or [
m
] key of remote commander to set
destination info if message “DEST UNFIX” appears.
10. Press the [ ] key of remote commander to select the
destination.
11. The message “DESTINY” appears.
12. Go to MODEL & DESTINATION check and press the [
]
key of remote commander.
13. Either one of the message as below appears.
Items Display
MODEL & AREA NOT FIX M D. D S T. U N F I X
MODEL NOT FIX M O D E L. U N F I X
DESTINATION NOT FIX D E S T. U N F I X
N105 N 1 0 5 x x x
DESTINATION RESET M D. D S T. U N F I X
xxx: Area display
14. Repeat step (12) onwards if message “DEST. UNFIX”
appears.
15. Set need to be reset and updated again if the message
appeared incorrectly.
16. Press the [
M
] or [
m
] key of remote commander goes to “MD.
DST.UNFIX”.
17. Press the [
] key of remote commander.
18. The set will power off and then power on by itself.
19. Start the setting again from step (1) onwards.
20. Perform SHIPMENT MODE if the message appears correctly.
21. The set will be power off itself and can be used as normal by
pressing [
?
/
1
] button.
MHL VBUS MODE
This mode is to display the MHL VBUS status.
Procedure:
1. Press the [
?
/
1
] button to turn on the main power.
2. While pressing [DISPLAY] button, press and release the
[MUSIC], [MOVIE], [A.F.D./2CH] button in order, the
message “VBUS STAT” appears.
3. Press the [
] key of the remote commander.
4. Either one of the message as below appears.
Items Display
No Error N O E R R O R
Current Stopped V . E R R O R x x
HDMI IN
76543210
0 : No error 1 : VBUS output is stopped
Example:
In 7 & In 0 are error : xx = 81
In 1 & In 0 are error : xx = 03
SIRCS MODE CHANGE
To change remote control mode (AV1<=>AV2).
Procedure:
1. While pressing [A.F.D./2CH], press the [
?
/
1
] button to turn
on the main power.
2. Either the message below appears. Select the desired mode.
Items Display
AV1 C. M O D E A V 1
AV2 C. M O D E A V 2