Sony TA-FA30ES Service Manual

MICROFILM
SERVICE MANUAL
INTEGRATED STEREO AMPLIFIER
AEP Model
UK Model
E Model
Australian Model
Chinese Model
SPECIFICATIONS
TA-FA30ES
Photo: GOLD model
System
Power Amplifier: Pure-complementary SEPP MOS FET power
amplifier with all stages directly coupled
Preamplifier: Low-noise, high-gain equalizer amplifier
Power section: Large-capacity power supply advanced STD
Rated output
4 ohms, 120 W + 120 W (DIN 0.7%, 1 kHz)
8 ohms, 80 W + 80 W (DIN 0.7%, 1 kHz)
Speaker Impedance
4 to 16 ohms
Output bandwidth (8 ohms)
10 Hz to 100 kHz (at 40 W output, and high-frequency distortion
rate of 0.08%)
Total harmonic distortion
0.008% (at 8 ohms, 10 W output)
Damping factor
100 (8 ohms, 1 kHz)
Intermodulation (1M) distortion (60 Hz : 7 kHz = 4 : 1)
0.008% (8 ohms)
Throughrate
125 V/µ sec, 250 V/µ sec (Inside)
Residual noise
Less than 100 µV (network A)
Equalizer deviation
PHONO MM: 20 Hz to 20 kHz, ± 5 dB
Frequency response
TUNER, CD, AUX, TAPE1/DAT, TAPE2/MD: 7 Hz to
100 kHz dB
S/N
PHONO MC: 78 dB (network A, 0.5 mV)
MM: 95 dB (network A, 5 mV)
TUNER, CD, AUX, TAPE1/DAT, TAPE2/MD: 105 dB
Inputs
Input sensitivity and impedance
PHONO MC: 0.17 mV, 100 ohms
MM: 2.5 mV, 50 kilohms
TUNER, CD, AUX, TAPE1/DAT, TAPE2/MD: 150 mV,
20 kilohms
Maximum input capability (1 kHz)
PHONO MC: 9 mV
MM: 150 mV
Outputs
Output level/impedance
REC OUT 1, 2: 150 mV, 1 kilohm
PHONES: 10 mW (at 8 ohms)
Tone controls
BASS (100 Hz): ± 7 dB
TREBLE (10 kHz): ± 7 dB
General
Power requirements
230 V AC, 50/60 Hz
Power consumption
220 W
Dimensions (approx) (w/h/d)
430 × 150 × 415 mm incl. projecting parts and controls
Mass (approx)
11.0 kg
Supplied accessories
Remote commander (remote ) RM-S326 (1)
Sony batteries R6 (size-AA) (2)
Design and specifications are subject to change without notice.
+0
–3

Sony TA-FA30ES Specifications

General

Brand	Sony
Model	TA-FA30ES
Category	Amplifier
Language	English

Summary

Product Specifications

Performance Metrics

Covers output power, distortion, frequency response, and S/N ratios.

Input/Output and Control Specifications

Details input sensitivity, output levels, and tone control ranges.

General Specifications

Includes power requirements, dimensions, mass, and supplied accessories.

Controls and Connections

Front Panel Controls

Describes the layout and function of front panel controls and indicators.

Rear Panel Connections

Identifies the various input/output jacks on the rear panel.

Disassembly Procedures

Front Panel and Case Removal

Outlines steps for removing the front panel and case.

Sub Panel Section Disassembly

Details the disassembly of the sub-panel section.

Electrical Adjustments

Bias Adjustment Procedure

Explains the procedure for setting the bias voltage on the main board.

Circuit Diagrams and Layouts

Printed Wiring Board Layouts

Shows the physical arrangement of components on various circuit boards.

Schematic Diagrams

Presents the detailed electrical schematics for the unit's sections.

Power Section Diagrams

Details the schematic for the power supply section.

Integrated Circuit (IC) Information

IC Block Diagrams

Visual representation of key integrated circuits.

IC Pin Function Descriptions

Detailed pinout and function of system controller and motor driver ICs.

Exploded Views

Front Panel Assembly Details

Illustrates the physical assembly of the front panel and associated parts.

Chassis and Internal Component Views

Shows exploded views of the chassis and internal board assemblies.

Electrical Parts List

Passive and Semiconductor Components

Lists resistors, capacitors, diodes, and transistors.

Active Components and Connectors

Lists connectors, switches, relays, ICs, and other miscellaneous parts.