SPECTRO SPECTROMAXx - User Manual

Questions and Answers

S
Sandra MorenoAug 5, 2025
What to do if limit values are not maintained during iCALising SPECTRO SPECTROMAXx?
- L
  Linda SmithAug 5, 2025
  If the limit values are not maintained during iCALising of your SPECTRO Measuring Instruments, it could be due to insufficient intensity. To address this, first, check the argon supply and sample. Then, clean the spark stand and adjust the electrode. Next, clean the light inlet window. Finally, ICALize the instrument again. If the issue persists, service center assistance may be required. Alternatively, high intensities may be the cause. In this case, check the shutter function and the plasma generator parameters.
N
natalie89Aug 11, 2025
How to troubleshoot SPECTRO SPECTROMAXx that cannot be switched on?
- B
  Bailey RobersonAug 11, 2025
  If your SPECTRO Measuring Instruments won't switch on, the issue might stem from a few common causes. First, ensure the power plug is correctly plugged in. Next, verify that power is available from the outlet. Lastly, inspect the fuse inside the power connection socket and replace it if it's defective.
M
Mrs. Lauren MorrisAug 18, 2025
Why are there low intensities in UV optics of SPECTRO SPECTROMAXx?
- B
  Brian SmithAug 18, 2025
  If you observe low intensities in UV optics of your SPECTRO Measuring Instruments, several factors could be responsible. One potential cause is a soiled light inlet window, which requires cleaning. Another cause can be low transmission, in which case you should use argon to rinse the optics using the “Rinse” function or the corresponding function key.
J
James ThompsonAug 23, 2025
What to do if the burn spot is incorrect on SPECTRO SPECTROMAXx?
- P
  perrycarlAug 23, 2025
  An incorrect burn spot on your SPECTRO Measuring Instruments can arise from several issues. The argon outlet might be clogged with condensate, requiring you to clean the spark stand including the argon outlet. Another potential cause is insufficient argon supply, so check the argon supply and pressure. Also, poor argon quality can lead to this problem, so connect new argon, referring to chapter 3 of the manual for specifications. An incorrect electrode gap may also be the cause, so clean the electrode and re-adjust the gap using the spacer. Finally, ensure that the samples have been prepared properly with a flat surface by grinding, turning, or milling.
J
Justin WhiteAug 29, 2025
Why are there low intensities in the air optics of SPECTRO SPECTROMAXx?
- J
  jamie60Aug 29, 2025
  If you are experiencing low intensities in the air optics of your SPECTRO Measuring Instruments, it may be due to a soiled light inlet window. Clean the light inlet window if required.

Summary

Description of Instrument

1.1 Description

Provides general details about the SPECTROMAXX instrument.

1.2 Function

Explains the core operational principle of the SPECTROMAXX analyzer.

1.3 Overview

Presents a visual overview of the instrument's main components.

Safety

2.1 User Information

Provides essential safety information and user responsibilities.

2.2 Intended Use

Outlines the proper applications and limitations of the instrument.

2.3 Prohibited Operating Conditions

Lists conditions under which the instrument must not be operated.

2.4 Residual Risks

Discusses potential hazards that cannot be fully eliminated.

Technical Data

Instrument Dimensions and Weight

Details physical specifications including height, width, depth, and weight.

Power and Environmental Specifications

Covers power supply, operating temperature, and humidity ranges.

Installation and Operation Requirements

Specifies requirements for installation location and EMC environment.

Transportation and Setting-up

4.1 Space Requirements

Details the necessary space dimensions for instrument installation.

4.2 Storage

Provides guidelines for proper storage conditions of the instrument.

4.3 Gas Supply

Instructions and information on connecting the argon gas supply.

Initial Start-up

5.1 Preparing the Instrument for Use

Steps to follow before switching on the instrument for initial operation.

Operation

6.1 Overview of Controls

Identifies and explains the instrument's control elements and their functions.

6.2 Switching on the Instrument

Step-by-step guide for powering on the SPECTROMAXX.

6.3 Switching off the Instrument

Procedures for safely shutting down the SPECTROMAXX.

6.4 Measuring Procedure

General safety warnings and information before performing a measurement.

6.4.1 Preparing the Measuring Procedure

Steps for setting up the instrument before starting a measurement.

6.4.2 Start the Measurement

Instructions for initiating and performing a measurement.

Maintenance

7.1 Maintenance Reminder

Information on the instrument's diagnostic system for maintenance tasks.

7.2 Maintenance Schedule

Outlines recommended maintenance tasks and their frequency.

7.3 Cleaning the UV Optics Light Inlet Window

Step-by-step guide for cleaning the UV optics light inlet window.

7.5 Cleaning the Spark Stand

Instructions for cleaning the spark stand, including safety warnings.

7.6 Exhaust Filter System - Change Filter Insert

Procedure for replacing the filter insert in the exhaust system.

7.7 Exhaust Filter System - Inspecting the Gas-Washing Bottle

Guide for inspecting and maintaining the gas-washing bottle.

7.8 Replacing the Filter Mats

Instructions for replacing the air filter mats in the housing.

Status Messages

Status Information

Explains status indicators displayed in the software footer.

Troubleshooting

Malfunctions and Causes

Lists common instrument malfunctions and their potential causes.

9.1 Error Messages

Details specific error messages and their remedies.

9.2 Diagnosis Tool

Explains how to use the LED status indicator for diagnostics.

Spare Parts and Consumables

Finding Spare Parts

Information on locating spare parts and consumables via the website.

De-commissioning

Authorized De-commissioning

Specifies who is permitted to de-commission the instrument.

Manufacturer Address

SPECTRO Analytical Instruments GmbH

Provides contact information for the instrument manufacturer.

SPECTRO SPECTROMAXx Specifications

General

Brand	SPECTRO
Model	SPECTROMAXx
Category	Measuring Instruments
Language	English

Related product manuals