SunStar Fortuna 5 Series - Specific Software Parameters; Group A: General Functions

2) Fortuna Series 5 Full Function Software Specific Parameters
(1) Group A Parameter General functions of sewing machine
I No. I Function Function Initial value Range
Minimum ^Bed of pedal (Itinit of sewing machine's minimum speed)
200spm 20-510
Maximum speed of pedal (limit of sewing machine's maximian speed)
4000spm 40-9960
Thread ti immer speed SOOspm 20-510
(Sewing machine speed from beginning to end of thread trimming when using CAM type)
Progran Unit-t-l stitch speed (0 Key's performance speed) iCOspm 2(h510
Lifting of needle plate with button A, dropping speed ( 's performance speed)
300spm 20-510
Pedal degree of acceleration (Pedal CunB) 255 1-255
( I ;Wienttie maximum speed is putin 255 steps)
7 Start Back-Tack Speed
8 End Back-Tack Speed
9 Thread Irimning operation lime
(The A24 used in PNEUMATIC = must tB 1)
(The Solenoid operation ti me)
10 Tension release operation ti me (The A24 used In PNEUMATIC = must Ire 1)
11 Tension release time (in CAM type, the used A24=must tB 0)
(In CAM t^, the tension release is the value of the moving CAM angle)
12 Waiting ti me for the next operation aflerthread bimming
(This is ti ie d^aying lime to cany out the next cation after thread ti imming is fnshed)
13 VMper operation ti me (Wper Solenoid operating ti me)
14 Waiting lime after wiper operation(pressef foot-lift etc.)
_15 Automatic presserfoot-lifl delaying time
16 Automatic presser foot-lift maintaning ti me
(Alter programmed ti me the presser footTrft is automaticalty released)
17 Automatic presser foot-lrft drop waiting time for next operation
(The delaying time, or the ti me that the foot-press^ lift is maintained,
the pedal is started until the presser foot-it drops and the sewing madtine Is started)
18 Seiedion for automatic kBt-presser lilt after tiread trimming
19 Seledion for pedal thread trirnming position
20 The maximum sewing qwed for the KM-1060BL-7 pressa'foot-lifl
with mutual crossing quantity of 4.8 - 7.0(mmj
21 Delaying ti me for complete release of KM-1060BL-7 BIT Solenoid
22 Seled to operate 2 start B/T
( /V ~'/^v\ ' )
23 Seled to operate 2 etxIBn'
A A A .
( / V ~^/ V V )
24 Seledion of thread trimming conditions
(selection according to sewing machine type)
25 tMielher ornot to use de^ult sequence when A24 = 1
(This is a sequence determined on A9 A10 value)
200ins 4~1020 (VMien doing an aging test, the value
is equ^ to llB ti vBad Irirnnrig time)
2H 0^55
4H020
48ms 4-1020 4ms
40ms 4-1020 4ms
100ms 4-1020 4ins
300x0.1sec 5-1000 O.Ssec
Hlft selection
0=slep backward ttvead trirrening
0=slep backward ti vead ti immii^
1=1 step backward thread trtinming
2=tiiread trirrvnmg at neutid position
10^ 2000spm 200-2000
200ms 4-1020ms
0 oii
4ms
Choose between lor 2
Choose between lor 2
0/1/2 0=CAM tyfB madiine
1=thread trimming up-st<^
2=thread trimming after kw-stop
0/1 0=8-55 exdusivesequaice is used
1=de^ult sequence is used
A
Caution
If the specific items of the parameter are changed carelessly, they could cause breakdown or damage the machine.
IhrerefiDre, the user must be well-trained before using it
From the library of Superior Sewing Machine & Supply LLC - www.supsew.com