Supermicro X9SRW-F - Installing DDR3 Memory; DIMM Installation; Removing Memory Modules

Chapter 2: Installation
2-9
JLAN1JLAN2
14
JUIDB1
JSTBY1
1
3
JIPMB1
JI2C1
1
5
Socket R
LGA 2011
CPU
DESIGNED IN USA
SXB2
SXB1B
1
JD1
JPWR1
1
T-SGPIO4
7
1
T-SGPIO3
7
1
T-SGPIO1
8
7
2
1
T-SGPIO2
87
1
JF1
1
2
19
20
JUSBKM
24
SXB1A
SAS2
SAS1
SAS3
SAS4
J17
H-HS2_2
SP1
JBT1
BD1
A
C
LED2
LE2
LE1
BT1
+
JOH1
JL1
1
R136
JVGA1
JTPM1
J26
J23
1
JCOM1
FAN5
FAN4
4
FAN3
FAN2
FAN1
JWF1
1
J4 J2 J3 J1
C241
JWP1
3
JI2C3 JI2C2
1
3
JPG1
JPB1
JP3
JPME1
JWD
JPL1
1
3
SXB1B: LEFT_WIO_MIDDLE
SXB2: RIGHT_WIO
SXB1A: LEFT_WIO_UP
WRITE PROTECT
JWP1:
USB
USB
1-2:RST
2-3:NIMI
JWD:
JI2C2/JI2C3
1-2:Enable
2-3:Disable
JPMB
OFF:NORMAL
ON:ME RECOVERY
JPME1:
VGA
UID
JTPM1: TPM/PORT80
DIMM4A DIMM4B DIMM3B
DIMM3A
KB/MOUSEUSB/2/3
JTPM1:TPM/PORT80
JSTBY1:STAND BY POWER FOR DOM
2-3:NMI
1-2:RST(DEFAULT)
JWD:WATCH DOG TIMER
JD1:
4-7:SPEAKER
1-2:PWR_LED
IPMI LAN
USB/0/1
1-2:ENABLE
2-3:DISABLE
JPL2:LAN2
JPL1:LAN1
2-3:DISABLE
1-2:ENABLE
JPB1: BMC
COM1
JBT1:CMOS CLEAR
LAN2
JL1
LAN1
DIMM2B
DIMM2A
JI2C1
2-3:Disable
1-2:Enable
JOH1:OVER HEAT LED
CPU
OFF:Disable
ON:Enable
2-3:DISABLE
1-2:ENABLE
:CHASSIS INTRUSION
I-SATA3
I-SATA4
I-SATA2
I-SATA1
I-SATA0
I-SATA5
DIMM1B
DIMM1A
JPG1: VGA
J29
1
3
J30
1
3
CPU1
CLOSE 1st
OPEN 1st
2-3 Installing DDR3 Memory
Note: Check the Supermicro website for recommended memory mod-
ules.
CAUTION
Exercise extreme care when installing or removing DIMM
modules to prevent any possible damage.
DIMM Installation
1. Insert the desired number of
DIMMs into the memory slots,
starting with DIMM1A, DIMM(see
the next page for the location). For
best performance, please use the
memory modules of the same type
and speed in the same bank.
2. Push the release tabs outwards
on both ends of the DIMM slot to
unlock it.
Release Tabs
Notches
3. Align the key of the DIMM mod-
ule with the receptive point on the
memory slot.
Press both notches
straight down into
the memory slot.
4. Align the notches on both ends of
the module against the receptive
points on the ends of the slot.
5. Use two thumbs together to press
the notches on both ends of the
module straight down into the slot
until the module snaps into place.
6. Press the release tabs to the lock
positions to secure the DIMM module
into the slot.
Removing Memory Modules
Reverse the steps above to remove the
DIMM modules from the motherboard.