Supermicro X9SRW-F - Rear Unit ID LED (LE2); IPMI Heartbeat LED (BD1); Onboard Standby Power LED (LED2)

Chapter 2: Installation
2-33
JLAN1JLAN2
14
JUIDB1
JSTBY1
1 3
JIPMB1
JI2C1
1
5
Socket R
LGA 2011
CPU
DESIGNED IN USA
SXB2
SXB1B
1
JD1
JPWR1
1
T-SGPIO4
7
1
T-SGPIO3
7
1
T-SGPIO1
8
7
2
1
T-SGPIO2
87
1
JF1
1
2
19
20
JUSBKM
24
SXB1A
SAS2
SAS1
SAS3
SAS4
J17
H-HS2_2
SP1
JBT1
BD1
A
C
LED2
LE2
LE1
BT1
+
JOH1
JL1
1
R136
JVGA1
JTPM1
J26
J23
1
JCOM1
FAN5
FAN4
4
FAN3
FAN2
FAN1
JWF1
1
J4
J2
J3
J1
C241
JWP1
3
JI2C3
JI2C2
1
3
JPG1
JPB1
JP3
JPME1
JWD
JPL1
1
3
SXB1B: LEFT_WIO_MIDDLE
SXB2: RIGHT_WIO
SXB1A: LEFT_WIO_UP
WRITE PROTECT
JWP1:
USB
USB
1-2:RST
2-3:NIMI
JWD:
JI2C2/JI2C3
1-2:Enable 2-3:Disable
JPMB
OFF:NORMAL ON:ME RECOVERY JPME1:
VGA
UID
JTPM1: TPM/PORT80
DIMM4A
DIMM4B
DIMM3B
DIMM3A
KB/MOUSEUSB/2/3
JTPM1:TPM/PORT80
JSTBY1:STAND BY POWER FOR DOM
2-3:NMI 1-2:RST(DEFAULT) JWD:WATCH DOG TIMER
JD1: 4-7:SPEAKER 1-2:PWR_LED
IPMI LAN
USB/0/1
1-2:ENABLE
2-3:DISABLE
JPL2:LAN2
JPL1:LAN1
2-3:DISABLE
1-2:ENABLE
JPB1: BMC
COM1
JBT1:CMOS CLEAR
LAN2
JL1
LAN1
DIMM2B
DIMM2A
JI2C1
2-3:Disable 1-2:Enable
JOH1:OVER HEAT LED
CPU
OFF:Disable ON:Enable
2-3:DISABLE
1-2:ENABLE
:CHASSIS INTRUSION
I-SATA3
I-SATA4
I-SATA2
I-SATA1
I-SATA0
I-SATA5
DIMM1B
DIMM1A
JPG1: VGA
J29
1
3
J30
1
3
CPU1
CLOSE 1st
OPEN 1st
B
A. Rear Unit ID LED
B. IPMI Heartbeat LED
C. Onboard Standby Power LED
A
C
IPMI Heartbeat LED (BD1)
The IPMI Heartbeat LED is located at BD1.
When BD1 blinks, the IPMI feature is func-
tioning properly. Refer to the table on the
right for details. Also see the layout below
for the LED location.
IPMI Heartbeat LED Indicator
LED Settings
Green: Blinking IPMI is ready for use
Off IPMI Off
Rear Unit ID LED (LE2)
The rear Unit ID LED is located at LE2 on
the back panel. This LED is used in con-
junction with the rear UID switch to provide
easy identication of a system that might be
in need of service.
Rear UID LED
LED Settings
Blue: Solid UID Toggled On
Off UID Toggled Off
Onboard Standby PWR LED (LE4)
LED Status
Status Denition
Off Power Supply is Off (Hard
Switch)
On Power Supply is On (Hard
Switch).
Onboard Standby Power LED (LED2)
An onboard Standby Power LED is located
at LED2. When LED2 is on, this indicates
that the AC power cable is connected and
the power supply hard switch is on. Make
sure to disconnect the power cable before
removing or installing any component. See
the layout below for the LED location.