Supermicro X9SRW-F - Onboard VGA Enable (JPG1); Unit Identifier Switch (Uid)

2-30
X9SRW Motherboard Series User’s Manual
JLAN1JLAN2
14
JUIDB1
JSTBY1
1 3
JIPMB1
JI2C1
1
5
Socket R
LGA 2011
CPU
DESIGNED IN USA
SXB2
SXB1B
1
JD1
JPWR1
1
T-SGPIO4
7
1
T-SGPIO3
7
1
T-SGPIO1
8
7
2
1
T-SGPIO2
87
1
JF1
1
2
19
20
JUSBKM
24
SXB1A
SAS2
SAS1
SAS3
SAS4
J17
H-HS2_2
SP1
JBT1
BD1
A
C
LED2
LE2
LE1
BT1
+
JOH1
JL1
1
R136
JVGA1
JTPM1
J26
J23
1
JCOM1
FAN5
FAN4
4
FAN3
FAN2
FAN1
JWF1
1
J4
J2
J3
J1
C241
JWP1
3
JI2C3
JI2C2
1
3
JPG1
JPB1
JP3
JPME1
JWD
JPL1
1
3
SXB1B: LEFT_WIO_MIDDLE
SXB2: RIGHT_WIO
SXB1A: LEFT_WIO_UP
WRITE PROTECT
JWP1:
USB
USB
1-2:RST
2-3:NIMI
JWD:
JI2C2/JI2C3
1-2:Enable 2-3:Disable
JPMB
OFF:NORMAL ON:ME RECOVERY JPME1:
VGA
UID
JTPM1: TPM/PORT80
DIMM4A
DIMM4B
DIMM3B
DIMM3A
KB/MOUSEUSB/2/3
JTPM1:TPM/PORT80
JSTBY1:STAND BY POWER FOR DOM
2-3:NMI 1-2:RST(DEFAULT) JWD:WATCH DOG TIMER
JD1: 4-7:SPEAKER 1-2:PWR_LED
IPMI LAN
USB/0/1
1-2:ENABLE
2-3:DISABLE
JPL2:LAN2
JPL1:LAN1
2-3:DISABLE
1-2:ENABLE
JPB1: BMC
COM1
JBT1:CMOS CLEAR
LAN2
JL1
LAN1
DIMM2B
DIMM2A
JI2C1
2-3:Disable 1-2:Enable
JOH1:OVER HEAT LED
CPU
OFF:Disable ON:Enable
2-3:DISABLE
1-2:ENABLE
:CHASSIS INTRUSION
I-SATA3
I-SATA4
I-SATA2
I-SATA1
I-SATA0
I-SATA5
DIMM1B
DIMM1A
JPG1: VGA
J29
1
3
J30
1
3
CPU1
CLOSE 1st
OPEN 1st
A
B
VGA Enable/Disable
Jumper Settings
Jumper Setting Denition
Pins 1-2 Enabled
Pins 2-3 Disabled
Onboard VGA Enable (JPG1)
JPG1 allows you to enable or disable the
onboard VGA connector. The default posi-
tion is on pins 1 and 2 to enable VGA. See
the table on the right for jumper settings.
Unit Identier Switch (UID)
The UID Switch (UID) is located on the I/O
back panel. When you push the UID Switch,
both the Rear UID LED and Front Panel
UID LED will turn on. Push the UID Switch
again to turn off both Indicators. These UID
Indicators provide easy identication of a
system unit that may be in need of service.
(For example, in a cabinet with several server
units installed.)
A. Onboard VGA Enable
B. UID Switch