Supermicro X9SRW-F - BMC Enable;Disable (JPB1); Watch Dog Reset (JWD)

Chapter 2: Installation
2-29
JLAN1JLAN2
14
JUIDB1
JSTBY1
1 3
JIPMB1
JI2C1
1
5
Socket R
LGA 2011
CPU
DESIGNED IN USA
SXB2
SXB1B
1
JD1
JPWR1
1
T-SGPIO4
7
1
T-SGPIO3
7
1
T-SGPIO1
8
7
2
1
T-SGPIO2
87
1
JF1
1
2
19
20
JUSBKM
24
SXB1A
SAS2
SAS1
SAS3
SAS4
J17
H-HS2_2
SP1
JBT1
BD1
A
C
LED2
LE2
LE1
BT1
+
JOH1
JL1
1
R136
JVGA1
JTPM1
J26
J23
1
JCOM1
FAN5
FAN4
4
FAN3
FAN2
FAN1
JWF1
1
J4
J2
J3
J1
C241
JWP1
3
JI2C3
JI2C2
1
3
JPG1
JPB1
JP3
JPME1
JWD
JPL1
1
3
SXB1B: LEFT_WIO_MIDDLE
SXB2: RIGHT_WIO
SXB1A: LEFT_WIO_UP
WRITE PROTECT
JWP1:
USB
USB
1-2:RST
2-3:NIMI
JWD:
JI2C2/JI2C3
1-2:Enable 2-3:Disable
JPMB
OFF:NORMAL ON:ME RECOVERY JPME1:
VGA
UID
JTPM1: TPM/PORT80
DIMM4A
DIMM4B
DIMM3B
DIMM3A
KB/MOUSEUSB/2/3
JTPM1:TPM/PORT80
JSTBY1:STAND BY POWER FOR DOM
2-3:NMI 1-2:RST(DEFAULT) JWD:WATCH DOG TIMER
JD1: 4-7:SPEAKER 1-2:PWR_LED
IPMI LAN
USB/0/1
1-2:ENABLE
2-3:DISABLE
JPL2:LAN2
JPL1:LAN1
2-3:DISABLE
1-2:ENABLE
JPB1: BMC
COM1
JBT1:CMOS CLEAR
LAN2
JL1
LAN1
DIMM2B
DIMM2A
JI2C1
2-3:Disable 1-2:Enable
JOH1:OVER HEAT LED
CPU
OFF:Disable ON:Enable
2-3:DISABLE
1-2:ENABLE
:CHASSIS INTRUSION
I-SATA3
I-SATA4
I-SATA2
I-SATA1
I-SATA0
I-SATA5
DIMM1B
DIMM1A
JPG1: VGA
J29
1
3
J30
1
3
CPU1
CLOSE 1st
OPEN 1st
A
A. Watch Dog Reset
B. BMC Enable
Watch Dog Reset (JWD)
Watch Dog (JWD) is a system monitor that
can reboot the system when a software
application hangs. Close Pins 1-2 to reset
the system if an application hangs. Close
Pins 2-3 to generate a non-maskable inter-
rupt signal for the application that hangs.
See the table on the right for jumper set-
tings. Watch Dog must also be enabled in
the BIOS.
Watch Dog
Jumper Settings
Jumper Setting Denition
Pins 1-2 Reset (default)
Pins 2-3 NMI
Open Disabled
B
BMC Enable/Disable (JPB1)
JPB1 is used to enable or disable the
BMC (Baseboard Management Control)
chip and the onboard IPMI connection.
This jumper is used together with the IPMI
settings in the BIOS. See the table on the
right for jumper settings.
BMC IPMI Enable/Disable
Jumper Settings
Settings Denition
Pins 1-2 Enabled (Default)
Pins 2-3 Disabled