Supermicro X9SRW-F - BIOS Recovery (JP3); ME Recovery (JPME1); VRM SMB Clock;Data (J29;J30)

Chapter 2: Installation
2-31
JLAN1JLAN2
14
JUIDB1
JSTBY1
1 3
JIPMB1
JI2C1
1
5
Socket R
LGA 2011
CPU
DESIGNED IN USA
SXB2
SXB1B
1
JD1
JPWR1
1
T-SGPIO4
7
1
T-SGPIO3
7
1
T-SGPIO1
8
7
2
1
T-SGPIO2
87
1
JF1
1
2
19
20
JUSBKM
24
SXB1A
SAS2
SAS1
SAS3
SAS4
J17
H-HS2_2
SP1
JBT1
BD1
A
C
LED2
LE2
LE1
BT1
+
JOH1
JL1
1
R136
JVGA1
JTPM1
J26
J23
1
JCOM1
FAN5
FAN4
4
FAN3
FAN2
FAN1
JWF1
1
J4
J2
J3
J1
C241
JWP1
3
JI2C3
JI2C2
1
3
JPG1
JPB1
JP3
JPME1
JWD
JPL1
1
3
SXB1B: LEFT_WIO_MIDDLE
SXB2: RIGHT_WIO
SXB1A: LEFT_WIO_UP
WRITE PROTECT
JWP1:
USB
USB
1-2:RST
2-3:NIMI
JWD:
JI2C2/JI2C3
1-2:Enable 2-3:Disable
JPMB
OFF:NORMAL ON:ME RECOVERY JPME1:
VGA
UID
JTPM1: TPM/PORT80
DIMM4A
DIMM4B
DIMM3B
DIMM3A
KB/MOUSEUSB/2/3
JTPM1:TPM/PORT80
JSTBY1:STAND BY POWER FOR DOM
2-3:NMI 1-2:RST(DEFAULT) JWD:WATCH DOG TIMER
JD1: 4-7:SPEAKER 1-2:PWR_LED
IPMI LAN
USB/0/1
1-2:ENABLE
2-3:DISABLE
JPL2:LAN2
JPL1:LAN1
2-3:DISABLE
1-2:ENABLE
JPB1: BMC
COM1
JBT1:CMOS CLEAR
LAN2
JL1
LAN1
DIMM2B
DIMM2A
JI2C1
2-3:Disable 1-2:Enable
JOH1:OVER HEAT LED
CPU
OFF:Disable ON:Enable
2-3:DISABLE
1-2:ENABLE
:CHASSIS INTRUSION
I-SATA3
I-SATA4
I-SATA2
I-SATA1
I-SATA0
I-SATA5
DIMM1B
DIMM1A
JPG1: VGA
J29
1
3
J30
1
3
CPU1
CLOSE 1st
OPEN 1st
D
ME Recovery (JPME1)
ME Recovery (JPME1) is used to enable
or disable the ME Recovery feature of the
motherboard. This jumper will reset Intel
ME values back to their default settings.
C
B
A
BIOS Recovery
Pin Denitions
Pin# Denition
1 Open (Default)
2 Ground
3 Recover
BIOS Recovery (JP3)
The BIOS Recovery (JP3) is used to en-
able or disable the BIOS Recovery feature
of the motherboard. Install the jumper on
pins 2-3 to begin the recovery process.
A. BIOS Recovery
B. ME Recovery
C. VRM SMB Clock (J29)
D. VRM SMB Data (J30)
ME Recovery
Pin Denitions
Pin# Denition
1 Open (Default)
2 Ground
3 Force Update
VRM SMB Clock/Data (J29/J30)
The VRM SMB Clock/Data is used to select
where the Voltage Regulator Module's Sys-
tem Management Bus clock signal (J29) or
Data (J30) is directed to. Select between
BMC or PCH.
VRM SMB Clock/Data
Pin Denitions
Pin# Denition
1 BMC (Default)
2 SMBCLK / SMBDAT
3 PCH