Need help?Do you have a question about the Tally Dascom DL-830 and is the answer not in the manual?
Key capabilities and design aspects of the thermal desktop label printer.
Detailed technical specifications of the printer, including print parameters and media handling.
Information on compatible media types like labels, receipts, and tickets.
Physical dimensions and weight of the printer.
Instructions for unpacking and checking printer contents and condition.
Overview of built-in and optional hardware components for the printer.
Identification and description of major physical parts of the printer.
Details on the printer's control panel, modes, and button functions.
Overview of printer operation modes and LCD indicators.
Lists the four main configuration menus available for the printer.
Demonstrates changing a printer setting using the control panel.
Explains various error messages shown on the LCD and their causes.
Step-by-step guide for installing the printer.
Factors to consider when choosing a location to install the printer.
Instructions for connecting the printer to a power source.
Guidance on adjusting the printer's media sensors for accurate feeding.
Explains the functions of Gap and Black Mark sensors.
Steps to reposition the Gap Sensor for optimal media alignment.
Steps to reposition the Black Mark Sensor for optimal media alignment.
Procedures for loading various types of media into the printer.
Detailed steps for correctly loading media rolls.
How to adjust media thickness and width settings for optimal print quality.
Instructions for installing the ribbon correctly.
Detailed steps for loading the ribbon roll.
Adjusting the Ribbon Balance Gear to fix ribbon wrinkles.
Adjusting the Ribbon Supply Leveler to fix ribbon wrinkles.
How to connect the printer to a PC using USB, LAN, or Parallel interfaces.
Step-by-step guide for installing the printer driver on a computer.
Instructions for installing the printer's configuration software.
Guide to establishing a connection using the Config Tool.
How to configure printer settings and firmware using the tool.
Configuring the printer for media using black marks for sensing.
Configuring the printer's network settings for LAN connectivity.
Configuring the printer's network settings for WiFi connectivity.
Configuring printer interface settings.
Process for updating the printer's firmware.
How to print the printer's current configuration settings.
A detailed list of all menu options and their settings.
Procedure to enable hex-dump mode for communication checks.
Process for automatic media alignment and registration.
Troubleshooting guide for common printer faults and their solutions.
Methods to reset the printer to its original factory settings.
Steps to safely remove jammed media from the printer.
Instructions for cleaning the printer's print head.
General guidelines for regular printer cleaning to maintain performance.
Pin assignment and connector details for the USB interface.
Pin assignment and connector details for the Ethernet interface.
Pin assignment and connector details for the Parallel interface.
Pin assignment and connector details for the Serial interface.
Description of WiFi functionality, network types, and parameters.
Instructions on how to enable and use the optional cutter.
Instructions on how to load media and use the optional peeler.
Table displaying ASCII characters and their corresponding codes.
Character set table for CP 437 (USA).
Character set table for CP 850.
Character set table for CP 860 (Portuguese).
Character set table for CP 863 (French).
Character set table for CP 865 (Nordic).
List of ZPL commands and their descriptions for printer control.
List of EPL commands and their descriptions for printer control.
List of TSPL commands and their descriptions for printer control.
General| Print Method | Direct Thermal |
|---|---|
| Resolution | 203 dpi |
| Interfaces | USB, Serial |
| Label Width Range | 25.4 mm to 114.3 mm |
| Memory | 4 MB Flash |
| Supported Barcodes | Code 39, Code 128, UPC-A, UPC-E, EAN-8, EAN-13, Interleaved 2 of 5, Codabar, POSTNET, PDF417, Data Matrix |
| Media Types | Direct thermal labels, tags |
| Media Roll Maximum Outer Diameter | 127 mm |
| Core Diameter | 25.4 mm (1 inch), 38.1 mm (1.5 inches) |
| Power Requirements | 100-240 VAC, 50/60 Hz |
| Operating Temperature | 5°C to 40°C (41°F to 104°F) |
To Next Page
