To Next PageTo Next PageWhat to do if I cannot start the digital turntable with the fader on my Technics Music Mixer?
If you cannot start the digital turntable with the fader on your Technics Music Mixer, ensure the FADER START switch is turned ON for the channel you intend to use. Also, verify that the digital turntable and mixer are connected using a control cable.
What to do if the fader (control slider) does not move smoothly on my Technics SH-MZ1200 Music Mixer?
If the fader (control slider) does not move smoothly on your Technics Music Mixer, it may be worn out. Replace it with a new fader. Contact your nearest dealer.
Input Sensitivity and Impedance| PHONO input sensitivity | 2.5 mV |
|---|---|
| PHONO input impedance | 47 kΩ |
| LINE input sensitivity | 250 mV |
| LINE input impedance | 10 kΩ |
| EFFECT RETURN input sensitivity | 250 mV |
| EFFECT RETURN input impedance | 47 kΩ |
| MIC input sensitivity | 0.7 mV |
| MIC input impedance | 1 kΩ |
Output Voltage and Impedance| MASTER 1, 2 (RCA) output voltage | 1 V |
|---|---|
| MASTER 1, 2 (RCA) output impedance | 600 Ω |
| MASTER 1 (XLR) output voltage | 1 V |
| MASTER 1 (XLR) output impedance | 600 Ω |
| MONITOR output voltage | 1 V |
| MONITOR output impedance | 1 kΩ |
| REC OUT output voltage | 250 mV |
| REC OUT output impedance | 1 kΩ |
| EFFECT SEND output voltage | 250 mV |
| EFFECT SEND output impedance | 1 kΩ |
| Headphone output power | 30 mW |
| Headphone output impedance | 32 Ω |
Frequency Response| MASTER 1, 2 frequency response | 20 Hz to 20 kHz |
|---|---|
| REC OUT frequency response | 20 Hz to 20 kHz |
| EFFECT RETURN frequency response | 20 Hz to 20 kHz |
| MIC frequency response | 20 Hz to 20 kHz |
Digital Audio| Coaxial digital input compatible sampling rate | 48 kHz/44.1 kHz/32 kHz |
|---|---|
| Coaxial digital output sampling rate | 44.1 kHz |
Equalizer Characteristics| CD/LINE/PHONO LOW EQ gain | +12 dB, –24 dB (50 Hz) |
|---|---|
| CD/LINE/PHONO MID EQ gain | +12 dB, –24 dB (1 kHz) |
| CD/LINE/PHONO HIGH EQ gain | +12 dB, –24 dB (10 kHz) |
| MIC LOW EQ gain | +12 dB, –24 dB (100 Hz) |
| MIC HIGH EQ gain | +12 dB, –24 dB (10 kHz) |
General| Power supply | AC 230-240 V, 50 Hz |
|---|---|
| Power consumption | 35 W |
| Dimensions (WxHxD) | 300 mm x 103 mm x 330 mm |
| Mass | 5.3 kg |
Warnings about placement, confinement, and ventilation to prevent hazards.
Precautions against rain, moisture, liquids, and naked flames.
Instructions on checking and replacing the fuse in the UK plug.
Guidance on plug suitability, cutting off unsuitable plugs, and wiring color codes.
Warnings about high voltage and DC power sources to prevent overload and fire.
Precautions for the AC lead, handling plugs, and preventing foreign matter ingress.
Diagrams for connecting speakers, amplifiers, and monitor amplifiers using phono and XLR cables.
Diagrams for connecting turntables, CD players, and cassette decks via various input terminals.
Instructions for selecting input sources and adjusting TRIM, HIGH, MID, LOW controls.
Guides on using channel faders, cross fader, and master level/balance controls.
How to cue channels, monitor effect return, select modes, and adjust volume.
How to use L/R SPLIT to adjust left and right channel input levels and sound.
Instructions for turning SEPARATE OUT ON for dual output and using the cross fader.
How to use the channel fader to start digital turntable playback.
How to use the cross fader to start digital turntable playback.
Instructions for alternate playback using the cross fader with CH1 and CH4.
Addresses problems like no power, no sound, and low volume, with checks and actions.
