EasyManuals Logo

Thecus N4200 User Manual

Thecus N4200
153 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #141 background imageLoading...
Page #141 background image
141
Chapter 7: Troubleshooting
Forgot My Network IP Address
If you forget your network IP address and have no physical access to the system,
you can find out the IP address by either looking directly onto Thecus IP storage LCD
panel, or by using the setup wizard to retrieve the IP of your Thecus IP storage.
1. Start the Setup Wizard, and it will automatically detect all Thecus IP storage
products on your network.
2. You should be able to find the IP address of Thecus IP storage which you
have forgotten in the Device Discovery screen.
Can't Map a Network Drive in Windows XP
You may have problems mapping a network drive under the following conditions:
1. The network folder is currently mapped using a different user name and
password. To connect using a different user name and password, first
disconnect any existing mappings to this network share.
2. The mapped network drive could not be created because the following error
has occurred: Multiple connections to a server or shared resource by
the same user, using more than one user name, are not allowed.
Disconnect all previous connections to the server or shared resource and try
again.
To check out existing network connections, type net use under the DOS prompt.
You may refer the URL below for more network mapping information.
http://esupport.thecus.com/support/index.php?_m=downloads&_a=viewdownload&downloaditemid
=57&nav=0
Restoring Factory Defaults
From the System menu, choose the Factory Default item and the Reset to
Factory Default screen appears. Press Apply to reset Thecus IP storagefactory
default settings.
WARNING
Resetting to factory defaults will not erase the data stored in the hard

Table of Contents

Other manuals for Thecus N4200

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Thecus N4200 and is the answer not in the manual?

Thecus N4200 Specifications

General IconGeneral
RAID levels0, 1, 5, 6, 10, JBOD
Storage drive capacity- GB
Supported file systemsExt3, XFS, ZFS
Storage drive interfaceSerial ATA
Total installed storage capacity8 TB
Number of storage drives installed-
Number of storage drives supported4
Internal memory1 GB
Internal memory typeDDR2
Bus typeDMI
SteppingB0
Tjunction100 °C
Processor codeSLBLA
Processor cache1 MB
Processor cores2
Processor modelD510
System bus rate- GT/s
Processor familyIntel Atom®
Processor socketBGA 559
Processor codenamePineview
Processing Die size87 mm²
Processor frequency1.66 GHz
Processor cache typeL2
Processor lithography45 nm
Processor manufacturerIntel
Processor package size22 x 22 mm
Conflict-Free processorNo
Processor operating modes64-bit
Thermal Design Power (TDP)13 W
Number of processors installed1
Physical Address Extension (PAE)32 bit
Memory bandwidth supported by processor (max)6.4 GB/s
Maximum internal memory supported by processor4 GB
Link/Act LEDYes
Expansion slotsPCI-e x1
Processor ARK ID43098
Networking featuresGigabit Ethernet
Compatible operating systems- Windows 2000/7/XP/2003/Vista; - UNIX/Linux; - Mac OS 9 / X
Maximum data transfer rate1000 Mbit/s
Supported network protocolsTCP/IP, Appletalk, SMB/CIFS, HTTP/HTTPS, FTP, NFS v3, AFP
Security algorithms256-bit AES
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Display typeOLED
Operating temperature (T-T)5 - 40 °C
Operating relative humidity (H-H)0 - 80 %
Number of Processing Die Transistors176 M
Memory channels supported by processorSingle

Related product manuals