Thermal Dynamics A80 CUTMASTER - Page 115

Thermal Dynamics A80 CUTMASTER

116 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

CUTMASTER A80

Manual 0-4985 A-11 APPENDIX

-V out (-) Polarity

Work1 (+) Polarity

Art # A-10288

5. Tighten the strain relief.

6. Replace the cover.

7. Connect the cable to negative and positive of Torch Height Control .

Table of Contents

Table of Contents5
General Information7
Important Safety Precautions7
Notes, Cautions and Warnings7
Publications8
Note, Attention Et Avertissement9
Precautions de Securite Importantes9
Documents de Reference11
Declaration of Conformity12
Statement of Warranty13
Section 2 System: Introduction15
- How to Use this Manual15
- Equipment Identification15
- Receipt of Equipment15
- Power Supply Specifications16
- Input Wiring Specifications17
- Power Supply Features18
Section 2 Torch: Introduction19
- 01 Scope of Manual19
- 02 General Description19
- 03 Specifications19
- 04 Options and Accessories20
- 05 Introduction to Plasma20
Section 3 System: Installation23
- Unpacking23
- Lifting Options23
- Power Supply Location and Mounting23
- Primary Input Power Connections23
- Gas Connections26
Section 3 Torch: Installation29
- 01 Torch Connections29
- 02 CNC Connection29
Section 4 System: Operation31
- Front Panel Controls / Features31
- Preparations for Operation32
Section 4 Torch: Operation35
- 01 Machine and Automated Torch Operation35
- 02 Automation Torch Parts Selection36
- 03 Machine and Hand Torch Parts Selection36
- 04 Cut Quality37
- T.04 Cut Quality37
- 05 General Cutting Information38
- 06 Hand Torch Operation39
- 07 Gouging 4T-842
Patent Information85
Section 5 System: Service87
- General Maintenance87
- Maintenance Schedule88
- Common Faults88
- Fault Indicator89
- Basic Troubleshooting Guide90
Section 5 Torch: Service95
- 01 General Maintenance95
- 02 Inspection and Replacement of Consumable Torch Parts96
  - Parts Lists97
- Introduction97
- Section 6 Parts Lists97
- Ordering Information97
- Power Supply Replacement97
- Replacement Power Supply Parts98
- Options and Accessories98
- Torch Replacement Parts SL100SV Torch (with Solenoid on Mounting Tube)100
- Torch Consumable Parts (SL100 SV)102
- Replacement Parts for Hand Torch103
Appendix 1: Sequence of Operation (Block Diagram105
Appendix 2: Data Tag Information106
Appendix 3: Torch Pin - out Diagrams107
Appendix 4: Torch Connection Diagrams108
Appendix 5: System Schematic, 208/460V Units110
Appendix 6: System Schematic, 400V/600V Units112
Appendix 7: Raw Arc Voltage114
Appendix 8: Publication History116

Related product manuals

Preview: Thermal Dynamics A60 CUTMASTER

Thermal Dynamics A60 CUTMASTER

Preview: Thermal Dynamics CUTMASTER A40

Thermal Dynamics CUTMASTER A40

Preview: Thermal Dynamics CUTMASTER A120

Thermal Dynamics CUTMASTER A120

Preview: Thermal Dynamics CUTMASTER

Thermal Dynamics CUTMASTER

Thermal Dynamics CutMaster 38

Preview: Thermal Dynamics CUTMASTER 39

Thermal Dynamics CUTMASTER 39

Preview: Thermal Dynamics CutMaster 58

Thermal Dynamics CutMaster 58

Preview: Thermal Dynamics 42 CUTMASTER

Thermal Dynamics 42 CUTMASTER

Preview: Thermal Dynamics CUTMASTER 60i

Thermal Dynamics CUTMASTER 60i

Preview: Thermal Dynamics CUTMASTER 151

Thermal Dynamics CUTMASTER 151

Preview: Thermal Dynamics 152 CUTMASTER

Thermal Dynamics 152 CUTMASTER

Preview: Thermal Dynamics CUTMASTER 102

Thermal Dynamics CUTMASTER 102