THUNDER TIGER TTR4571 - User Manual

1/6 Rare Bear ARF
Unlimited Pylon Racer
1
Thunder Tiger Rare Bear ARF Airplane (TTR4571)
Distributed in North America by Ace Hobby Distributors,Inc.• 2055 Main Street,Irvine,CA 92614
Telephone:949.833.0088 •
www.acehobby.com • E-mail:service@acehobby.com
Specification:
Wingspan:63" (1600mm)
Length:55.5" (1410mm)
Weight: 10.5~11 lbs (4800–5000g)
Engine:.60~ .90 2C .91~1.20 4C
Radio:5CH
Servo:5 servos plus 1 retract servo
Warranty
This kit is guaranteed to be free from defects in material and workmanship at the date of purchase. It
does not cover any damage caused by use or modification. The warranty does not extend beyond the
product itself and is limited only to the original cost of the kit. By the act of building this user-assembled
kit,the user accepts all resulting in liability for damage caused by the final product. If the buyer is not
prepared to accept this liability,it can be returned new and unused to the place of purchase for a refund.
Notice: Adult Supervision Required
This is not a toy. Assembly and flying of this product requires adult supervision.
Read through this book completely and become familiar with the assembly and flight of this airplane.
Inspect all parts for completeness and damage. If you encounter any problems,call us for help.
JE6660 V2
Assembly Manual

THUNDER TIGER TTR4571 Specifications

General

Brand	THUNDER TIGER
Model	TTR4571
Category	Toy
Language	English

Summary

Introduction and Pre-Assembly

Pre-Assembly Notes

Guidance on reading instructions and checking kit contents before assembly.

Recommended Tools and Materials

Essential Adhesives and Tools

Lists necessary adhesives like CA and epoxy, and essential tools for model building.

RC System, Engine, and Accessories

Details required RC system, recommended engines, propellers, and optional accessories.

Parts Drawings and Identification

Fuselage and Plywood Components

Illustrations and part numbers for fuselage and plywood components.

Main Wing and Tail Surfaces

Diagrams of the main wing assembly and horizontal tail sections.

Canopy, Cockpit, and Decals

Drawings for canopy, cockpit, decorative elements, and decal sheets.

Gear, Tank, and Hardware Illustrations

Diagrams of tail gear, fuel tank, engine mounts, linkages, and hardware.

Wing Assembly

Aileron Servo and Control Horn Setup

Step-by-step guide for installing the aileron servo and control horn.

Retract Well Preparation and Installation

Steps for fitting and securing the retract gear and its mounting.

Fuselage Assembly

Landing Gear and Retract Door Assembly

Instructions for installing wheel axles, retract doors, and wheel wells.

Firewall, Bulkhead, and Battery Box Integration

Guidance on assembling firewalls, bulkheads, and the battery box for structural integrity.

Tail Feathers Assembly

Horizontal Stabilizer and Torque Rod Installation

Steps for assembling the horizontal stabilizer and installing the elevator torque rod.

Rudder Installation

Elevator Pushrod and Servo Connection

Connecting the elevator pushrod to the servo and torque rod links.

Rudder Torque Rod and Hinge Attachment

Installing the rudder torque rod and securing hinges to the vertical fin.

Tail Gear Section

Steering Arm, Torque Rod Mount, and Gear Assembly

Assembling steering, mounting torque rod retainer, and the tail gear.

Tail Steering Linkage and Control Setup

Creating the control loop for tail steering linkage and connecting it.

Fuel Tank Installation

Bottom Tail Cover and Fuel Tank Setup

Installing the bottom tail cover and connecting fuel lines for the tank.

Engine Installation

Engine Mount, Engine, and Throttle Linkage

Installing the engine mount, securing the engine, and setting up the throttle linkage.

Retract Servo Installation

Retract Servo Tray, Linkage, and Pushrod

Installing the retract servo tray, linkage, and connecting the pushrod.

Wing Joining and Battery Installation

Joining wing halves, routing pushrods, and installing the battery for CG.

Cowling Installation

Battery Box Cover, Switch Harness, and Receiver

Securing battery box, installing switch harness, and mounting the receiver.

Engine Cowling Fitting and Airflow

Attaching engine cowling doublers and fitting the cowl for airflow.

Cockpit Installation and Final Details

Cowling Vent Filing and Canopy Fitting

Filing cowling for air, fitting cockpit, and securing the canopy.

Final Assembly and Decal Application

Completing cockpit/canopy installation and applying decals.

Balance and Flight Preparation

Control Throws and Center of Gravity (CG)

Setting control throws and adjusting the center of gravity for flight stability.

Flying Site and Battery Notes

Guidance on selecting flying locations and notes on battery charging.