Topcon GTS-239W - Page 166

To Next Page

To Previous Page

Bluetooth

™

and the Bluetooth

™

logos are trademarks owned by Bluetooth

™

SIG, Inc., USA and licensed to Topcon

Corporation.

Main Page

Default Chapter3
- General Handling Precautions3
- Display for Safe Use4
- Safety Cautions4
- User5
- Exceptions from Responsibility5
- Safety Standard for Laser Beam6
- Symbol Mark While the Laser Is Emitting6
- Table of Contents7
- Standard Set Composition10
1 Nomenclature and Functions11
- Nomenclature11
- Display13
- Operating Key14
- Function Key (Soft Key)15
- Star Key Mode16
- Serial Signal RS-232C Connector18
- Bluetooth™ Communication18
- Laser Plummet ON/OFF (Only for Laser Plummet Type)19
2 Preparation for Measurement20
- Power Connection20
- Setting Instrument up for Measurement21
- Power Switch Key on22
- Battery Power Remaining Display23
- Vertical and Horizontal Angle Tilt Correction24
- How to Enter Alphanumeric Characters26
3 Angle Measurement28
- Measuring Horizontal Angle Right and Vertical Angle28
- Switching Horizontal Angle Right/Left29
- Measuring from the Required Horizontal Angle29
  - Setting by Holding the Angle29
  - Setting a Horizontal Angle from the Keys30
- Vertical Angle Percent Grade(%) Mode30
- Repetition Angle Measurement31
- Buzzer Sounding for Horizontal Angle 90° Increments32
- Compasses ( Vertical Angle)33
4 Distance Measurement34
- Setting of the Atmospheric Correction34
- Setting of the Correction for Prism Constant34
- Distance Measurement (Continuous Measurement)34
- Distance Measurement (N-Time Measurement/Single Measurement)35
- Fine Mode/Tracking Mode/Coarse Mode36
- Stake out (S.O)37
- Offset Measurement38
5 Coordinate Measurement47
- Setting Coordinate Values of Occupied Point47
- Setting Height of the Instrument48
- Setting Height of Target (Prism Height)48
- Execution of Coordinate Measuring49
6 SPECIAL MODE (Menu Mode)50
- Application Measurement (PROGRAMS)51
- Setting the GRID FACTOR65
- Setting Illumination of Display and Cross Hairs66
- Setting Mode 167
- Setting Contrast of Display72
7 Data Collection73
- Preparation75
- Data Collect Offset Measurement Mode82
- NEZ Auto Calculation89
- Editing PCODE Library [PCODE INPUT]90
- Setting Parameter of Data Collect [CONFIG.]91
8 Layout92
- Preparation94
- Executing a Layout99
- Setting a New Point101
  - Side Shot Method101
  - Resection Method103
9 Memory Manager Mode107
- Display Internal Memory Status108
- Searching Data109
- File Maintenance113
- Coordinate Data Direct Key Input116
- Delete a Coordinate Data from a File117
- Editing PCODE Library118
- Data Communications119
- Initialization122
10 Set Audio Mode123
11 Setting the Prism Constant Value124
12 Setting Atmospheric Correction125
- Calculation of Atmospheric Correction125
- Setting of Atmospheric Correction Value125
13 Correction for Refraction and Earth Curvature130
- Distance Calculation Formula130
14 Power Source and Charging131
- On-Board Battery BT-52QA131
15 Detach/Attach of Tribrach133
16 Selecting Mode134
- Items of the Selecting Mode134
- How to Set Selecting Mode136
17 Check and Adjustment138
- Checking and Adjusting of Instrument Constant138
- Checking the Optical Axis139
- Checking/Adjusting the Theodolite Functions140
- How to Set the Instrument Constant Value147
- Adjustment of Compensation Systematic Error of Instrument148
- Reference Frequency Check Mode150
18 Precautions151
19 Special Accessories152
20 Battery System155
21 Prism System156
22 Error Displays157
23 Specifications159
Appendix162
- Dual Axis Compensation162
- Precaution When Charging or Storing Batteries164

Topcon GTS-239W - Page 166

Table of Contents

Related product manuals