Toro 03675 - User Manual

Questions and Answers

J
Jeffrey BakerSep 18, 2025
Why is a single cutting unit lowering very slowly or not at all on my Toro 03675 Lawn Mower?
- T
  Tricia SalazarSep 19, 2025
  If a single cutting unit lowers very slowly or not at all on your Toro Lawn Mower, inspect for binding issues, replace damaged components, and clear or repair flow control orifices. This could be due to a binding lift arm or lift cylinder, a damaged lift cylinder, a plugged or damaged flow control orifice in the lift control manifold for the affected cutting unit, or a stuck or damaged check valve in the lift control manifold.
M
Megan MartinezSep 23, 2025
What to do if the wheel motor will not turn on my Toro 03675?
- T
  Timothy RangelSep 23, 2025
  If the wheel motor on your Toro Lawn Mower will not turn, check and repair the brakes and replace the wheel motor if necessary. This could be due to binding brakes or a worn or damaged wheel motor.
M
Molly McdanielSep 23, 2025
Why does the single wheel motor turn while unloaded, but slows down or stops when load is applied on my Toro Lawn Mower?
- B
  Brian ColemanSep 23, 2025
  If the single wheel motor turns while unloaded, but slows down or stops when a load is applied on your Toro Lawn Mower, replace the worn or damaged wheel motor. This is caused by a worn or damaged wheel motor.
D
Dawn MosleySep 23, 2025
Why won't the wheel motors hold a load when the traction pedal is in neutral on my Toro 03675?
- M
  Mark BrownSep 23, 2025
  If the wheel motors on your Toro Lawn Mower will not hold a load when the traction pedal is in neutral, check the charge pressure and replace or repair the valve plate and/or piston shoes. This could be due to low charge pressure or scored valve plate and/or piston shoes in the piston pump.
K
Kerry FlynnNov 23, 2025
What to do if my Toro Lawn Mower has no traction in either direction?
- K
  Kathleen HowellNov 23, 2025
  If your Toro Lawn Mower has no traction in either direction while the engine speed remains constant, several issues could be the cause. The hydraulic fluid level in the hydraulic tank might be low, so fill it to the proper level. The piston (traction) pump bypass valve could be open, requiring you to check, repair, or replace it. Also, the charge pressure may be low, so check it and make adjustments as necessary. Other potential causes include the parking brake being applied, dragging, or binding (release or fix the parking brake), the traction control linkage being incorrectly adjusted, disconnected, binding, or damaged (inspect and repair the traction control linkage), the flushing valve in the piston (traction) pump not seating or being damaged (inspect and repair or replace the flushin...
K
Kevin VazquezNov 24, 2025
Why is my Toro 03675 hydraulic system operating hot?
- Q
  qtaylorNov 24, 2025
  If your Toro Lawn Mower's hydraulic system is operating hot, several factors could be responsible. High traction system pressure due to load or dragging brakes may be the cause, so reduce the load or check for dragging brakes. A low hydraulic fluid level or a loose or clogged inlet filter can also lead to overheating, so fill the hydraulic tank to the recommended level and check the inlet filter. Other potential causes include contaminated hydraulic fluid, fluid viscosity being too light (replace with appropriate viscosity fluid), a damaged or plugged oil cooler (inspect and repair or replace), obstructed oil cooler airflow (clear obstructions), a plugged hydraulic fluid filter (replace), an open or damaged piston pump bypass valve (check and repair or replace), a stuck-open gear pump reli...
W
whitejeffreyNov 26, 2025
Why is the traction response of my Toro Lawn Mower sluggish?
- M
  Michelle BeasleyNov 26, 2025
  If the traction response of your Toro Lawn Mower is sluggish, the following could be the reasons: the piston (traction) pump bypass valve is open or damaged (check and repair or replace the bypass valve), the brake is dragging or binding (inspect and fix any dragging or binding brakes), the charge pressure is low (check and adjust the charge pressure), the hydraulic fluid is very cold (allow the hydraulic fluid to warm up to operating temperature), the piston (traction) pump check valve, relief valve, and/or flushing valve is leaking (inspect and repair or replace leaking valves), the piston (traction) pump or wheel motor(s) is worn or damaged (inspect and repair or replace worn or damaged components), the charge relief valve in the piston (traction) pump is not seating or is damaged (insp...
K
Kevin LeAug 23, 2025
Why is hydraulic fluid leaking from my Toro 03675 system?
- D
  Danielle AllenAug 23, 2025
  Hydraulic fluid might be leaking from your Toro Lawn Mower due to several reasons. The fitting(s), hose(s), or tube(s) may be loose or damaged; in this case, you should check and tighten or replace them. Also, the O-ring(s) or seal(s) may be missing or damaged, requiring replacement.
A
Amanda MoralesSep 8, 2025
Why is the steering inoperative or sluggish on my Toro Lawn Mower?
- F
  Felicia GrimesSep 9, 2025
  If the steering on your Toro Lawn Mower is inoperative or sluggish, identify and correct the causes affecting steering operations. Possible causes include worn or binding steering components, a binding steering cylinder, low oil level in the hydraulic reservoir, a stuck or damaged steering relief valve, internal leaks in the steering cylinder, a worn or damaged steering control valve, or a worn or damaged gear pump section.
N
Nathaniel MullinsSep 7, 2025
What to do if there is no traction in either direction on my Toro Lawn Mower?
- K
  Kevin ParkerSep 8, 2025
  If you have no traction in either direction with your Toro Lawn Mower, locate the cause of the trouble and correct it. Potential causes include the parking brake dragging or binding, misadjusted or damaged traction control linkage, low oil level in the hydraulic reservoir, a loosened traction pump bypass valve, a damaged flushing valve in the traction pump, a damaged piston pump check valve, low charge pressure, or worn or damaged wheel motor(s) and/or piston pump.