What to do if my Toro Lawn and Garden Equipment machine does not start immediately after shutting it off?
If your Toro Lawn and Garden Equipment machine does not start immediately after shutting it off, the machine may not have powered down completely. Allow the machine to completely power down before starting it again.
What to do if my Toro Lawn and Garden Equipment machine does not resume operation after idling?
If your Toro Lawn and Garden Equipment machine doesn't resume operation after idling, it might be in Power Save Mode. To resolve this, rapidly move a traction lever twice or shut off and start the machine again.
What does SPN 4992, FMI 16 or FMI 3 mean on my Toro Lawn and Garden Equipment?
SPN 4992, FMI 16 or FMI 3 indicates a battery high voltage issue. Ensure that the battery voltage is correct and the cable connections are secure; also, make sure the battery is in good condition.
Why is my Toro Lawn and Garden Equipment machine not charging?
Your Toro Lawn and Garden Equipment machine may not be charging because the temperature is either above 55°C (131°F) or below 2°C (35.6°F). Charge the machine in conditions between 2°C (35.6°F) and 55°C (131°F).
What to do if loader arms lower quickly on Toro Lawn and Garden Equipment?
If the loader arms on your Toro Lawn and Garden Equipment lower 5 cm (2 inches) quickly and then stop, the cylinder seals may be leaking. Replace the seals to fix this issue.
General| Battery Voltage | 48 V |
|---|---|
| Power Source | Electric |
| Ground Speed Forward | 4.5 mph (7.2 km/h) |
| Hinge Pin Height | 72.5 in (184.2 cm) |
| Operating Height | 72.5 in (184 cm) |
| Max Speed | 4.5 mph |
| Rated Operating Capacity | 515 lb (234 kg) |
Information regarding Proposition 65 warnings for chemicals in California.
Essential safety precautions for operating the machine to prevent injury or death.
Procedure to inspect and maintain the machine's hydraulic fluid level.
Steps for charging the machine's batteries.
Description and function of the machine's control panel.
Details on the operation and positions of the machine's key switch.
Information on the automatic parking brake engagement and disengagement.
Guidance on using the reference bars for machine control and stability.
Instructions on how to operate the machine using the traction control.
How to operate the loader arms and tilt the attachment using the control lever.
Operation of the auxiliary hydraulics controls for attachments.
Overview of the InfoCenter LCD display for machine status and diagnostics.
Explanation of icons displayed on the InfoCenter screen.
Synopsis of options available within the InfoCenter main menu.
Details on accessing and interpreting machine fault codes.
Lists total operating hours for key components and controls.
Records hydraulic motor starts, charge cycles, and low battery alerts.
Procedure to calibrate the machine's traction control.
Indicates battery inputs, outputs, voltage, and state of charge.
Displays status, health, and utilization of the CAN bus.
Shows motor control inputs and outputs for diagnostics.
Pre-operation checks and procedures.
Critical safety guidelines to follow before operating the machine.
Fundamental safety rules for safe machine operation.
Daily maintenance tasks to ensure machine readiness.
Safety precautions during machine operation.
Key safety rules to follow while operating the machine.
Specific safety guidelines for operating on slopes.
Safety procedures when working near utility lines.
Step-by-step guide to starting the machine.
Procedure for safely shutting down the machine.
Information on the machine's automatic sleep mode.
Instructions for correctly attaching accessories to the machine.
Procedure for connecting hydraulic hoses to attachments.
Steps for safely removing attachments from the machine.
How to switch between attachment modes like Backhoe or Bucket.
Safety guidelines to follow after operating the machine.
General safety practices for post-operation procedures.
Safety precautions related to charging the machine's batteries.
Crucial safety guidelines to follow before performing maintenance.
Procedure for using cylinder locks during maintenance.
Steps for installing cylinder locks before maintenance.
Instructions for removing and storing cylinder locks.
Procedure for removing the machine's hood.
Steps for removing the lower front cover.
Procedure for greasing the machine's fittings.
Safety precautions for electrical system maintenance.
Instructions for operating the battery disconnect switch.
Procedure for checking tire tread wear.
Instructions for checking and torquing wheel lug nuts.
Specifications for the drive-motor gear oil type and capacity.
Procedure for adjusting machine controls.
Safety precautions for hydraulic system maintenance.
Procedure to safely relieve hydraulic system pressure.
Procedure for removing debris from the machine.
Guidelines for pressure washing the machine safely.
Safety precautions for storing the machine.
Procedure for properly storing the machine.
Common machine problems and their corrective actions.
Explanation of battery-charger error codes and their solutions.
To Next Page
